| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: fix locked bus on SMBus block-read of 0 (atomic)
SMBus 3.1 6.5.7 allows a Block Read byte count of 0, but the atomic
(polling) path rejects it as -EPROTO. Worse, it returns without a
NACK+STOP: the next receive cycle has already started, so the target
keeps holding SDA and the bus stays stuck until a power cycle for
this i2c controller.
Reading I2DR to obtain the count likewise arms the next byte on the
count > I2C_SMBUS_BLOCK_MAX path, which also returned -EPROTO directly
and left the bus held.
Handle both: NACK the in-flight dummy byte (TXAK) and extend msgs->len so
the existing last-byte handling emits STOP; the dummy byte is discarded.
A count of 0 is a valid empty block read; a count above
I2C_SMBUS_BLOCK_MAX is still reported as -EPROTO, but only after the bus
has been released.
The interrupt-driven path has the same flaw from a later commit and is
fixed separately, as it carries a different Fixes: tag and stable range. |
| In the Linux kernel, the following vulnerability has been resolved:
xen/gntdev: fix error handling in ioctl
When gntdev_ioctl_map_grant_ref() fails to copy the operation result
back to userspace after successfully adding the mapping to the list,
the error path returns -EFAULT without releasing the reference
acquired by gntdev_alloc_map(). The mapping remains in priv->maps
with a refcount of 1, causing a memory leak and a dangling list
entry.
Additionally, gntdev_add_map() may modify map->index to avoid overlap
with existing mappings. Therefore, the index returned to userspace
must be obtained after gntdev_add_map() completes.
Fix this by holding the mutex across gntdev_add_map(), retrieving
the correct index, and copy_to_user(). If copy_to_user() fails,
remove the mapping from the list and release the reference while
still holding the lock.
Fix these issues by properly handling all error cases. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix CAN frame rx/tx statistics
KCSAN detected a data race within the bcm_rx_handler() when two CAN frames
have been simultaneously received and processed in a single rx op by two
different CPUs.
Use atomic operations with (signed) long data types to access the
statistics in the hot path to fix the KCSAN complaint.
Additionally simplify the update and check of statistics overflow by
using the atomic operations in separate bcm_update_[rx|tx]_stats()
functions. The rx variant runs under bcm_rx_update_lock to prevent
races when resetting the two rx counters; the tx variant runs under
bcm_tx_lock and only needs to guard its own counter's overflow.
As the rx path resets its values already at LONG_MAX / 100, there is
no conflict between the two locking domains (bcm_rx_update_lock vs.
bcm_tx_lock) even for ops that use both paths.
The rx statistics update and the frames_filtered update in
bcm_rx_changed() were previously performed in two separate
bcm_rx_update_lock sections. For an rx op subscribed on all interfaces
(ifindex == 0), bcm_rx_handler() can run concurrently on different
CPUs, so a counter reset by one CPU between these two sections could
leave frames_filtered larger than frames_abs on another CPU, producing
a bogus (even negative) reduction percentage in procfs. Update the
statistics in the same critical section as bcm_rx_changed() to close
this gap, which also removes the now unneeded extra lock/unlock pair
around the traffic_flags calculation. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix data race on rx_stamp/rx_ifindex in bcm_rx_handler()
For an rx op subscribed on all interfaces (ifindex == 0), the same op
is registered once in the shared per-netns wildcard filter list, so
bcm_rx_handler() can run concurrently on different CPUs for frames
arriving on different net devices.
op->rx_stamp and op->rx_ifindex were written before bcm_rx_update_lock was
taken, allowing concurrent writers to race each other - including a torn
store of the 64-bit rx_stamp on 32-bit platforms.
Beyond a torn store bcm_send_to_user() must report the timestamp/ifindex
of the very same frame whose content it is delivering. So the assignment
is placed in the same unbroken bcm_rx_update_lock section as the content
comparison.
As a side effect, the RTR-request frame feature (which never reach
bcm_send_to_user()) no longer updates rx_stamp/rx_ifindex, since only
the notification path needs them. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-verity: fix a possible NULL pointer dereference
Fix a possible NULL pointer dereference dm_verity_loadpin_is_bdev_trusted
if the device has no table. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-verity: make error counter atomic
The error counter "v->corrupted_errs" was not atomic, thus it could be
subject to race conditions. The call to
dm_audit_log_target("max-corrupted-errors") may be skipped due to the
races. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: hpsa: Fix DMA mapping leak on IOACCEL2 reset path
If phys_disk->in_reset is set, the function returns directly without
undoing the resources acquired for the command. Add the missing error
cleanup by unmapping the IOACCEL2 SG chain block when needed, unmapping
the SCSI command, and dropping the outstanding IOACCEL command count
before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix memory leak in lpfc_sli4_driver_resource_setup()
The memory allocated for mboxq using mempool_alloc() is not freed in
some of the early exit error paths. Fix that by moving the
mempool_free() call to an earlier point after last use. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: xen: scsiback: Free the command tag on the TMR submit-failure path
scsiback_device_action() obtains a command tag in
scsiback_get_pend_req() and submits a task-management request with
target_submit_tmr(). When target_submit_tmr() fails it returns < 0 and
scsiback jumps to the err: label, which sends a response but frees
nothing, leaking the tag.
Impact: a pvSCSI guest can leak the command tags of a LUN's session,
stopping the LUN, by issuing VSCSIIF_ACT_SCSI_ABORT or RESET requests
whenever target_submit_tmr() fails.
transport_generic_free_cmd() cannot be used here. By the time
target_submit_tmr() returns an error it has already run
__target_init_cmd() (so se_cmd->cmd_kref is one, not zero), and on its
target_get_sess_cmd() error path it has freed se_cmd->se_tmr_req via
core_tmr_release_req() while leaving SCF_SCSI_TMR_CDB set and the
pointer dangling. Letting the command release run target_free_cmd_mem()
would then double-free se_tmr_req.
Use the same helper, which returns just the tag, on this path too. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: vub300: fix use-after-free on probe failure
The vub300 driver lifetime-manages its controller state using
vub300->kref, with vub300_delete() freeing the mmc host when the last
reference is dropped. The probe error path after the inactivity timer has
been armed still bypasses that lifetime rule, however, and falls through
to mmc_free_host() directly if mmc_add_host() fails.
The race window is between arming the inactivity timer and reaching the
probe error unwind after mmc_add_host() fails:
probe thread timer/workqueue
------------ ---------------
kref_init(&vub300->kref) ref = 1
kref_get(&vub300->kref) ref = 2, timer ref
add_timer(inactivity_timer) fires after one second
|
| race window
|<---------------------------------------------------->
|
mmc_add_host(mmc)
inactivity timer fires
vub300_queue_dead_work()
kref_get() ref = 3
queue_work(deadwork)
mmc_add_host() fails
timer_delete_sync()
mmc_free_host(mmc)
frees vub300
deadwork runs
use-after-free
The inactivity timeout is one second, so this would require
mmc_add_host() to both fail and take more than one second to do so. This
is unlikely to happen in practice, but the error path is still wrong.
timer_delete_sync() only waits for the timer callback itself. It does
not flush deadwork that the callback may already have queued. As a
result, queued deadwork can still hold a kref while the probe error path
directly frees the backing mmc host, including the vub300 storage.
Fix this by using the same lifetime mechanism as disconnect. Clear
vub300->interface so that the timer callback and any queued deadwork
return early and drop their references, then drop the initial probe
reference and return without falling through to err_free_host. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: libertas_tf: fix use-after-free in lbtf_free_adapter()
lbtf_free_adapter() calls timer_delete(&priv->command_timer), which does
not wait for a running command_timer_fn() callback. lbtf_free_adapter()
runs on the teardown path right before ieee80211_free_hw() frees priv,
both in lbtf_remove_card() and in the probe error path. command_timer is
armed by mod_timer() in lbtf_cmd() whenever a firmware command is sent.
command_timer_fn() dereferences priv. If a command times out as the
device is removed, command_timer_fn() runs concurrently with teardown and
dereferences priv after it has been freed.
This is the same use-after-free that commit 03cc8f90d053 ("wifi: libertas:
fix use-after-free in lbs_free_adapter()") fixed in the sibling libertas
driver. The libertas_tf variant has the identical pattern and was left
unchanged. Use timer_delete_sync() so any in-flight callback completes
before priv is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
posix-cpu-timers: Use u64 multiplication in update_rlimit_cpu()
update_rlimit_cpu() converts the RLIMIT_CPU value to nanoseconds with
u64 nsecs = rlim_new * NSEC_PER_SEC;
On 32-bit kernels both rlim_new (unsigned long) and NSEC_PER_SEC
(1000000000L) are 32-bit, so the multiplication is performed in unsigned
long and truncated for rlim_new > 4 seconds before being widened to u64.
The same file already casts to u64 for the matching computation in
check_process_timers():
u64 softns = (u64)soft * NSEC_PER_SEC;
As a result, the truncated value is installed into the CPUCLOCK_PROF
expiry cache (nextevt), causing the process CPU timer to be programmed
to fire prematurely for any RLIMIT_CPU soft limit >= 5 seconds. The
actual SIGXCPU/SIGKILL decision in check_process_timers() already casts
to u64 and is therefore correct, so limit enforcement is not broken;
only the expiry-cache programming is wrong. Apply the same cast here so
both paths convert rlim_cur identically.
64-bit kernels are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: tegra: do not call pinctrl for GPIO direction
tegra_gpio_direction_input() and tegra_gpio_direction_output() already
program the GPIO controller direction registers directly. The additional
pinctrl_gpio_direction_input/output() calls do not add a Tegra pinctrl
operation, because the Tegra pinmux ops provide GPIO request/free
handling but no gpio_set_direction hook.
The extra call still enters the pinctrl core and takes pctldev->mutex.
Shared GPIO users can call the direction path while holding their
per-line spinlock, so this otherwise redundant pinctrl direction call can
sleep in an atomic context.
This was found by our static analysis tool and then confirmed by manual
review of tegra_gpio_probe(), the Tegra GPIO direction callbacks and the
Tegra pinctrl ops. The reviewed path has a default non-sleeping
struct gpio_chip while the direction callback still enters the pinctrl
mutex path.
A directed runtime validation kept the same non-sleeping chip registration
and drove:
gpio_shared_proxy_direction_output()
gpiod_direction_output_raw_commit()
tegra_gpio_direction_output()
pinctrl_gpio_direction_output()
Lockdep reported a sleep-in-atomic warning with the shared GPIO spinlock
held and pinctrl_get_device_gpio_range() plus tegra_gpio_direction_output()
on the stack.
Do not mark the whole chip as can_sleep to paper over this: can_sleep
describes whether get()/set() may sleep, and Tegra value access is MMIO.
Remove the redundant pinctrl direction calls and keep pinctrl involvement
in the existing request/free path. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ena: clean up XDP TX queues when regular TX setup fails
create_queues_with_size_backoff() creates XDP TX queues before setting
up the regular TX path. If the subsequent allocation or creation of
regular TX queues fails, the error handling paths omit the teardown of the
XDP TX queues, leading to a resource leak.
Fix this by explicitly destroying the XDP TX queue subset at the two
missing failure points.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have
an ENA device to test with, no runtime testing was able to be performed. |
| In the Linux kernel, the following vulnerability has been resolved:
ipmi: fix refcount leak in i_ipmi_request()
When a caller provides a `supplied_recv` message to i_ipmi_request(),
the function increments the user's `nr_msgs` reference count. If an
error occurs later, the out_err cleanup path only frees the recv_msg
if the function allocated it itself (i.e., !supplied_recv). In the
supplied_recv case the cleanup is skipped, leaving the reference count
elevated. The caller ipmi_request_supply_msgs() does not release the
supplied_recv on error, so the reference is permanently leaked.
Fix this by explicitly reverting the reference count operations when a
supplied recv_msg with a valid user pointer is present in the error
path: decrement nr_msgs and drop the user's kref. |
| In the Linux kernel, the following vulnerability has been resolved:
bnx2x: fix potential memory leak in bnx2x_alloc_mem_bp()
If the allocation of fp[i].tpa_info fails, the error path will not free
the struct bnx2x_fastpath allocated earlier, as it is not linked to the
bp structure yet. Fix that by linking it immediately after allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libata-core: Reject an invalid concurrent positioning ranges count
ata_dev_config_cpr() takes the number of range descriptors from buf[0]
of the concurrent positioning ranges log (up to 255), which the device
reports independently of the log size in the GPL directory. The count is
then walked at a fixed 32-byte stride in two places with no bound: the
log read here, and the INQUIRY VPD page B9h emitter, which writes one
descriptor per range into the fixed 2048-byte ata_scsi_rbuf. A device
reporting a count larger than its own log overflows the read buffer (up
to 7704 bytes past a 512-byte slab), and a count above 62 overflows the
response buffer on the emit side.
Bound the count once, on probe, against both the log the device returned
and the number of descriptors the VPD B9h response buffer can hold
(ATA_DEV_MAX_CPR, derived from the rbuf size). Reject an out-of-range
count with a warning; this keeps the emitter in bounds with no separate
change there. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/resctrl: Fix double-add of pseudo-locked region's RMID to free list
A pseudo-locked group's RMID is freed when it is created. On unmount
rmdir_all_sub() unconditionally frees all RMID of all groups, resulting
in a double-free of the pseudo-locked group's RMID. The consequence of this
is that the original free results in the pseudo-locked group's RMID being
added to the rmid_free_lru linked list and the second free then attempts
to add the same RMID entry to the rmid_free_lru again.
Do not double-free a pseudo-locked group's RMID. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup/cpuset: rebind mm mempolicy to effective_mems, not mems_allowed
Creating a child cpuset where cpuset.mems is never set leads to a div/0
when a VMA mempolicy with MPOL_F_RELATIVE_NODES rebinds in response to a
CPU hotplug event.
Reproduction steps:
1) Create a cgroup w/ cpuset controls (do not set cpuset.mems)
2) Move the task into the child cpuset
3) Create a VMA mempolicy for that task with MPOL_F_RELATIVE_NODES
4) unplug and hotplug a cpu
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 1 > /sys/devices/system/cpu/cpu1/online
5) mempolicy rebind does a div/0 in mpol_relative_nodemask on the
call to __nodes_fold()
The cpuset code passes (cs->mems_allowed) which is not guaranteed to have
nodes to the rebind routine. Use cs->effective_mems instead, which is
guaranteed to have a non-empty nodemask once we reach that code path.
[ david: add a comment, slightly rephrase description ] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix memory leak in ieee80211_register_hw()
If kmemdup() fails while copying supported band structures, the error
path jumps to fail_rate. This skips rate_control_deinitialize() and
leaks the initialized local->rate_ctrl.
Fix this by adding a fail_band label that shares the rate-control cleanup
path before falling through to the remaining teardown.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have a
suitable mac80211 device/driver combination to test with, no runtime
testing was able to be performed. |
