| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix memory leak in lpfc_sli4_driver_resource_setup()
The memory allocated for mboxq using mempool_alloc() is not freed in
some of the early exit error paths. Fix that by moving the
mempool_free() call to an earlier point after last use. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: xen: scsiback: Free the command tag on the TMR submit-failure path
scsiback_device_action() obtains a command tag in
scsiback_get_pend_req() and submits a task-management request with
target_submit_tmr(). When target_submit_tmr() fails it returns < 0 and
scsiback jumps to the err: label, which sends a response but frees
nothing, leaking the tag.
Impact: a pvSCSI guest can leak the command tags of a LUN's session,
stopping the LUN, by issuing VSCSIIF_ACT_SCSI_ABORT or RESET requests
whenever target_submit_tmr() fails.
transport_generic_free_cmd() cannot be used here. By the time
target_submit_tmr() returns an error it has already run
__target_init_cmd() (so se_cmd->cmd_kref is one, not zero), and on its
target_get_sess_cmd() error path it has freed se_cmd->se_tmr_req via
core_tmr_release_req() while leaving SCF_SCSI_TMR_CDB set and the
pointer dangling. Letting the command release run target_free_cmd_mem()
would then double-free se_tmr_req.
Use the same helper, which returns just the tag, on this path too. |
| In the Linux kernel, the following vulnerability has been resolved:
bnx2x: fix potential memory leak in bnx2x_alloc_mem_bp()
If the allocation of fp[i].tpa_info fails, the error path will not free
the struct bnx2x_fastpath allocated earlier, as it is not linked to the
bp structure yet. Fix that by linking it immediately after allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix memory leak in ieee80211_register_hw()
If kmemdup() fails while copying supported band structures, the error
path jumps to fail_rate. This skips rate_control_deinitialize() and
leaks the initialized local->rate_ctrl.
Fix this by adding a fail_band label that shares the rate-control cleanup
path before falling through to the remaining teardown.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have a
suitable mac80211 device/driver combination to test with, no runtime
testing was able to be performed. |
| In the Linux kernel, the following vulnerability has been resolved:
reset: sunxi: fix memory region leak on ioremap failure
In sunxi_reset_init(), when ioremap() fails, the memory region obtained
via request_mem_region() is not released, leading to a resource leak.
Add an err_mem_region label to properly release the memory region before
freeing the data structure. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: free mapping node on duplicate reloc root insert
__add_reloc_root() allocates a mapping_node before inserting it into
rc->reloc_root_tree. If rb_simple_insert() finds an existing entry, it
returns the existing rb_node and leaves the newly allocated node unlinked.
The error path then returns -EEXIST without freeing the new node. Since
the node was never inserted into reloc_root_tree, the later cleanup in
put_reloc_control() cannot find it either.
Free the newly allocated node before returning -EEXIST.
The callers currently assert that -EEXIST should not happen, so this is a
defensive cleanup for an unexpected duplicate insert path. If the path is
ever reached, the local allocation should still be released. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix root leak if its reloc root is unexpected in merge_reloc_roots()
If we have an unexpected reloc_root for our root, we jump to the out label
but never drop the reference we obtained for root, resulting in a leak.
Add a missing btrfs_put_root() call. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ipw2100: fix potential memory leak in ipw2100_pci_init_one()
The memory allocated in the ipw2100_alloc_device() function is not freed
in some of the error paths in ipw2100_pci_init_one(). Fix that by
converting the direct return into a goto to the error path return.
The error path when pci_enable_device() fails cannot jump to fail, since
at this point priv is not set, so perform error handling inline. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: libertas: fix memory leak in helper_firmware_cb()
helper_firmware_cb() neglects to free the single-stage firmware image
after a successful async load, leading to a memory leak in the USB
firmware-download path.
Fix this memory leak by calling release_firmware() immediately after
lbs_fw_loaded() returns.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
the current wireless tree.
An x86_64 allyesconfig build showed no new warnings. As we do not have
compatible Libertas USB hardware for exercising this firmware-download
path, no runtime testing was able to be performed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hsr: fix memory leak on slave unregistration by removing synced VLANs
When an HSR master device is brought UP, it auto-adds VLAN 0 via
vlan_vid0_add(), which propagates VID 0 to its slave devices (slave A and B).
If a slave device is later unregistered while HSR is active (e.g., during
netns cleanup or interface destruction), hsr_del_port() is called to
detach the slave port from the HSR master. However, hsr_del_port() currently
does not delete the VLAN IDs that were synced to the slave device by HSR.
As a result, the slave device retains a refcount on VID 0 (and any other
synced VLANs). When the slave device is destroyed, its vlan_info /
vlan_vid_info structure remains allocated, leading to a memory leak.
Fix this by calling vlan_vids_del_by_dev(port->dev, master->dev) in
hsr_del_port() before unlinking slave A or slave B ports, matching the
propagation logic in hsr_ndo_vlan_rx_add_vid() / hsr_ndo_vlan_rx_kill_vid()
and the cleanup behavior in bonding and team drivers. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/gem: Do not leak siblings[] on proto context error
After a successful BALANCE/PARALLEL_SUBMIT extension on context
creation, error during processing of next user extension leaks
the siblings[] array. Fix that.
Discovered using AI-assisted static analysis confirmed by
Intel Product Security.
(cherry picked from commit aa65e0a4b51b3b54b53e4142aaa2d997aa1061ff) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix bo->pin leaking in amdgpu_bo_create_reserved
amdgpu_bo_create_reserved() only allocates a new BO when
*bo_ptr (struct amdgpu_bo **bo_ptr as input parameter) is
NULL, it simply skips creation when *bo_ptr is non-NULL.
But it unconditionally reserves, pins, gart allocates
and maps the BO afterwards.
When the same non-NULL BO pointer is passed in again,
for example firmware buffers that live in adev and are
re-loaded on every resume / cp_resume / start
under AMDGPU_FW_LOAD_DIRECT, amdgpu_bo_pin() just increases
pin_count unconditionally, however the matching teardown only unpins
once, so pin_count never drops to zero, so TTM is not able
to move, swap or evict a BO, causing BO leaks.
This commit fixes this issue by only pinning the bo
once at creation, and repeated calls no longer
take additional pin references.
(cherry picked from commit 3ddc0ae76202c447b6aec61e907b852bc94671cf) |
| In the Linux kernel, the following vulnerability has been resolved:
media: cx231xx: fix devres lifetime
USB drivers bind to USB interfaces and any device managed resources
should have their lifetime tied to the interface rather than parent USB
device. This avoids issues like memory leaks when drivers are unbound
without their devices being physically disconnected (e.g. on probe
deferral or configuration changes).
Fix the driver state lifetime so that it is released on driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
media: pci: dm1105: Free allocated workqueue
Destroy allocated workqueue in remove() callback to free its resources,
thus fixing memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
media: pwc: Drain fill_buf on start_streaming() failure
pwc_isoc_init() submits its isochronous URBs with
usb_submit_urb(.., GFP_KERNEL) in a loop. After the first URB is
submitted, its completion handler pwc_isoc_handler() can run on another
CPU before the loop finishes:
start_streaming()
pwc_isoc_init()
usb_submit_urb(urbs[0], GFP_KERNEL)
pwc_isoc_handler(urbs[0])
pdev->fill_buf =
pwc_get_next_fill_buf(pdev)
usb_submit_urb(urbs[i>0], ..) -> fails
pwc_isoc_cleanup(pdev) /* kills URBs */
return ret;
pwc_cleanup_queued_bufs(pdev, VB2_BUF_STATE_QUEUED)
pwc_get_next_fill_buf() detaches a buffer from pdev->queued_bufs and
stores it in pdev->fill_buf. The error path in start_streaming() only
drains pdev->queued_bufs, so the buffer parked in pdev->fill_buf is
leaked. vb2_start_streaming() then triggers
WARN_ON(owned_by_drv_count).
stop_streaming() already handles this since commit 80b0963e1698
("[media] pwc: fix WARN_ON"), which added the fill_buf drain in the
teardown path but not in the start_streaming() error path. Mirror that
handling on failure so start_streaming() returns with no buffer owned
by the driver.
Issue identified by automated review of the INV-003 series at
https://sashiko.dev/ |
| In the Linux kernel, the following vulnerability has been resolved:
media: saa7134: Fix a possible memory leak in saa7134_video_init1
In saa7134_video_init1(), the return value of the first
saa7134_pgtable_alloc() is not checked. If it fails, the function
continues as if successful, leaving the driver with an invalid page
table. Additionally, if vb2_queue_init() for the VBI queue fails after
the video queue page table has been allocated, the allocated memory is
not freed before returning. The second saa7134_pgtable_alloc() also
lacks a return value check. Errors occur during device probing before
the device is fully registered, the normal cleanup path in
saa7134_finidev() is not executed, leading to memory leaks and
potential use of uninitialized DMA resources.
Check the return value of both saa7134_pgtable_alloc() calls and
propagate errors. On failure of any later step, free allocated page
tables to avoid memory leaks. Ensure control handlers are also
released on error to prevent further resource leakage.
Found by code review. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: kxsd9: fix runtime PM imbalance on write_raw() error
kxsd9_write_raw() takes a runtime PM reference with pm_runtime_get_sync()
but returns -EINVAL directly when a scale with a non-zero integer part is
requested, skipping the matching pm_runtime_put_autosuspend(). This leaks
a runtime PM usage-counter reference on every such write, after which the
device can no longer autosuspend.
Set the error code and fall through to the existing put instead of
returning early. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: mediatek: Fix IRQ domain leak when port fails to enable
When mtk_pcie_enable_port() fails, mtk_pcie_port_free() removes the port
from pcie->ports and frees the port structure. However, the IRQ domains set
up earlier by mtk_pcie_init_irq_domain() are never freed.
Fix this by refactoring mtk_pcie_irq_teardown() into a per-port helper,
mtk_pcie_irq_teardown_port(), and calling it from mtk_pcie_setup() when
mtk_pcie_enable_port() fails. Since the IRQ teardown must only happen in
the probe error path (during resume, child devices may have active MSI
mappings and the NOIRQ context prohibits sleeping locks),
mtk_pcie_enable_port() is changed to return an error code so callers can
distinguish the two paths and act accordingly.
This issue was reported by Sashiko while reviewing the EcoNet EN7528 SoC
support series. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/nop: fix file reference leak with IOSQE_FIXED_FILE
NOP file-acquisition support choses between a fixed (registered) file and
a normal fget()'d file based on its own IORING_NOP_FIXED_FILE flag in
sqe->nop_flags. However, a request's REQ_F_FIXED_FILE is set
independently from the generic IOSQE_FIXED_FILE sqe flag during request
init, before the issue handler runs.
If a NOP is submitted with IOSQE_FIXED_FILE set (so REQ_F_FIXED_FILE is
set) but without IORING_NOP_FIXED_FILE, io_nop() takes the normal path
and grabs a real reference via io_file_get_normal(). On completion,
io_put_file() only drops the reference when REQ_F_FIXED_FILE is clear,
so the fget()'d file is never released and leaks:
BUG: memory leak
unreferenced object 0xffff88800f42c240 (size 176):
kmem_cache_alloc_noprof+0x358/0x440
alloc_empty_file+0x57/0x180
path_openat+0x44/0x1e50
do_file_open+0x121/0x200
do_sys_openat2+0xa7/0x150
__x64_sys_openat+0x82/0xf0
Decide between fixed and normal file acquisition from REQ_F_FIXED_FILE,
the same way io_assign_file() does for every other opcode, and fold
IORING_NOP_FIXED_FILE into REQ_F_FIXED_FILE at prep time. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: Fix next buffer leak in receive_encrypted_standard()
receive_encrypted_standard() allocates next_buffer before checking
whether the number of compound PDUs already reached MAX_COMPOUND. If
the limit check fails, the function returns immediately and the newly
allocated next_buffer is not assigned to server->smallbuf/server->bigbuf,
making it leaked.
Move the MAX_COMPOUND check before allocating next_buffer. |
