| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - reject an oversized device packet size
mms114_interrupt() reads a packet of touch data from the device into a
fixed-size on-stack buffer
struct mms114_touch touch[MMS114_MAX_TOUCH];
which holds MMS114_MAX_TOUCH (10) events of MMS114_EVENT_SIZE (8) bytes,
i.e. 80 bytes. The length of the I2C read into it is taken verbatim from
the device:
packet_size = mms114_read_reg(data, MMS114_PACKET_SIZE);
if (packet_size <= 0)
goto out;
...
error = __mms114_read_reg(data, MMS114_INFORMATION, packet_size,
(u8 *)touch);
packet_size is a single device register byte (0x0F) and the only check
is the lower bound packet_size <= 0; it is never bounded against the
size of touch[]. A malfunctioning, malicious or counterfeit controller
(or an attacker tampering with the I2C bus) can report a packet_size of
up to 255, so __mms114_read_reg() writes up to 175 bytes past the end of
touch[] on the IRQ-thread stack: a stack out-of-bounds write that can
overwrite the stack canary, saved registers and the return address.
A well-formed device never reports more than the buffer holds, so reject
an oversized packet and drop the report, consistent with the handler's
other error paths, rather than reading past the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Remove latent out-of-bounds access in IOMMU debugfs
In iommu_mmio_write() and iommu_capability_write(), the variables
dbg_mmio_offset and dbg_cap_offset are declared as int. However, they
are populated using kstrtou32_from_user(). If a user provides a
sufficiently large value, it can become a negative integer.
Prior to this patch, the AMD IOMMU debugfs implementation was already
protected by different mechanisms.
1. #define OFS_IN_SZ 8 ensures the user string <= 8 bytes, so
e.g. 0xffffffff isn't a valid input.
if (cnt > OFS_IN_SZ)
return -EINVAL;
2. Implicit type promotion in iommu_mmio_write(), dbg_mmio_offset is int
and iommu->mmio_phys_end is u64
if (dbg_mmio_offset > iommu->mmio_phys_end - sizeof(u64))
return -EINVAL;
3. The show handlers would currently catch the negative number and
refuse to perform the read.
Replace kstrtou32_from_user() with kstrtos32_from_user() to parse the
input, and check for negative values to explicitly prevent out-of-bounds
memory accesses directly in iommu_mmio_write() and
iommu_capability_write(). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Fix page overflow in sev_dbg_crypt() for ENCRYPT path
In sev_dbg_crypt(), the per-iteration transfer length is bounded by
the source page offset (PAGE_SIZE - s_off) but not by the destination
page offset (PAGE_SIZE - d_off). When d_off > s_off, the encrypt
path (__sev_dbg_encrypt_user) performs a read-modify-write using a
single-page intermediate buffer (dst_tpage):
1. __sev_dbg_decrypt() expands the size to round_up(len + (d_off & 15), 16)
before issuing the PSP command. If len + (d_off & 15) > PAGE_SIZE,
the PSP writes beyond the end of the 4096-byte dst_tpage allocation.
2. The subsequent memcpy()/copy_from_user() into
page_address(dst_tpage) + (d_off & 15) of 'len' bytes overflows
by up to 15 bytes under the same condition.
Trigger example: s_off = 0, d_off = 1, debug.len = PAGE_SIZE -
the PSP is instructed to write round_up(4097, 16) = 4112 bytes to
a 4096-byte buffer.
Fix by also bounding len by (PAGE_SIZE - d_off), the same check that
sev_send_update_data() already performs for its single-page guest
region.
==================================================================
BUG: KASAN: slab-use-after-free in sev_dbg_crypt+0x993/0xd10 [kvm_amd]
Write of size 4095 at addr ff110062293bb009 by task sev_dbg_test/228214
CPU: 96 UID: 0 PID: 228214 Comm: sev_dbg_test Tainted: G U W 7.0.0-smp--5ce9b0c48211-dbg #156 PREEMPTLAZY
Tainted: [U]=USER, [W]=WARN
Hardware name: Google Astoria/astoria, BIOS 0.20250817.1-0 08/25/2025
Call Trace:
<TASK>
dump_stack_lvl+0x54/0x70
print_report+0xbc/0x260
kasan_report+0xa2/0xd0
kasan_check_range+0x25f/0x2c0
__asan_memcpy+0x40/0x70
sev_dbg_crypt+0x993/0xd10 [kvm_amd]
sev_mem_enc_ioctl+0x33c/0x450 [kvm_amd]
kvm_vm_ioctl+0x65d/0x6d0 [kvm]
__se_sys_ioctl+0xb2/0x100
do_syscall_64+0xe8/0x870
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
The buggy address belongs to the physical page:
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x7fe72b6a0 pfn:0x62293bb
memcg:ff11000112827d82
flags: 0x1400000000000000(node=1|zone=1)
raw: 1400000000000000 0000000000000000 dead000000000122 0000000000000000
raw: 00000007fe72b6a0 0000000000000000 00000001ffffffff ff11000112827d82
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ff110062293bbf00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ff110062293bbf80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ff110062293bc000: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^
ff110062293bc080: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ff110062293bc100: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
==================================================================
Disabling lock debugging due to kernel taint
[sean: add sample KASAN splat, Fixes, and stable@] |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Add bounds check for firmware runtime memory
Validate that the firmware runtime memory specified in the image
header is properly aligned and sized to hold the firmware image.
This prevents errors during memory allocation and image transfer. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: io_ti: fix heap overflow in get_manuf_info()
get_manuf_info() reads le16_to_cpu(rom_desc->Size) bytes from the
device I2C EEPROM into a buffer allocated with kmalloc_obj(), which
is sizeof(struct edge_ti_manuf_descriptor) = 10 bytes.
The Size field comes from the device and is only validated (in
check_i2c_image()) to make sure the descriptor fits within
TI_MAX_I2C_SIZE (16384 bytes), not against the destination buffer size.
A malicious USB device can therefore set Size to any value up to 16377,
causing a heap overflow of up to 16367 bytes when plugged into a host
running this driver.
valid_csum() is called after read_rom() and also iterates
buffer[0..Size-1], compounding the out-of-bounds access.
Fix by rejecting descriptors with unexpected length before calling
read_rom().
[ johan: amend commit message; also check for short descriptors ] |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: io_ti: fix heap overflow in build_i2c_fw_hdr()
build_i2c_fw_hdr() allocates a fixed-size buffer of
(16*1024 - 512) + sizeof(struct ti_i2c_firmware_rec) bytes, then
copies le16_to_cpu(img_header->Length) bytes into it without
validating that Length fits within the available space after the
firmware record header.
img_header->Length is a __le16 from the firmware file and can be
up to 65535. check_fw_sanity() validates the total firmware size
but not img_header->Length specifically.
Fix by rejecting images where img_header->Length exceeds the
available destination space. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Clamp XDomain response data copy to allocation size
tb_xdp_properties_request() derives the per-packet copy length from
the response header without checking that it fits in the previously
allocated data buffer. A malicious peer can set its length field
larger than the declared data_length, causing memcpy to write past
the kcalloc allocation.
Clamp the per-packet copy length so that the cumulative offset
never exceeds data_len. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix buffer overflow in SDMA queue checkpoint/restore on GFX11
The v11 MQD manager incorrectly assigned the CP-compute variants of
checkpoint_mqd/restore_mqd for KFD_MQD_TYPE_SDMA queues. These functions
use sizeof(struct v11_compute_mqd) (2048 bytes) instead of sizeof(struct
v11_sdma_mqd) (512 bytes), causing a 1536-byte overflow.
During CRIU checkpoint of an SDMA queue on Navi3x:
- checkpoint_mqd() reads 2048 bytes from a 512-byte SDMA MQD buffer,
leaking 1536 bytes of adjacent GTT memory to userspace
During CRIU restore:
- restore_mqd() writes 2048 bytes into a 512-byte SDMA MQD buffer,
corrupting 1536 bytes of adjacent GTT memory (often the ring buffer
or neighboring MQDs)
This is a copy-paste regression unique to v11. All other ASIC backends
(cik, vi, v9, v10, v12) correctly use the SDMA-specific variants.
Add checkpoint_mqd_sdma() and restore_mqd_sdma() functions that properly
handle the smaller v11_sdma_mqd structure, matching the pattern used in
other MQD managers.
(cherry picked from commit 6fa41db7ffdec97d62433adf03b7b9b759af8c2c) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Clamp HDMI HDCP2 rx_id_list read to buffer size
[Why & How]
During HDCP 2.x repeater authentication over HDMI, the driver reads the
sink's RxStatus register and extracts a 10-bit message size field (max
value 1023). This value is used as the read length for the ReceiverID
list without being clamped to the size of the destination buffer
rx_id_list[177]. A malicious HDMI repeater could advertise a message
size larger than the buffer, causing an out-of-bounds write during the
I2C read.
Clamp the read length in mod_hdcp_read_rx_id_list() to the size of the
rx_id_list buffer, matching the approach already used in the DP branch.
(cherry picked from commit 229212219e4247d9486f8ba41ef087358490be09) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Clamp VBIOS HDMI retimer register count to array size
[Why & How]
The VBIOS integrated info tables (v1_11 and v2_1) contain HdmiRegNum and
Hdmi6GRegNum fields that are used as loop bounds when copying retimer I2C
register settings into fixed-size arrays (dp*_ext_hdmi_reg_settings[9]
and dp*_ext_hdmi_6g_reg_settings[3]). These u8 fields are not validated
before use, so a malformed VBIOS can specify values up to 255, causing an
out-of-bounds heap write during driver probe.
Clamp each register count to the destination array size using min_t()
before the copy loops, in both get_integrated_info_v11() and
get_integrated_info_v2_1().
(cherry picked from commit 5a7f0ef90195940c54b0f5bb85b87da55f038c69) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix NULL deref and buffer over-read in SDP debugfs
[Why & How]
dp_sdp_message_debugfs_write() dereferences connector->base.state->crtc
without checking for NULL. A connector can be connected but not bound to
any CRTC (e.g. after hot-plug before the next atomic commit), causing a
kernel crash when writing to the sdp_message debugfs node.
The function also ignores the user-provided size argument and always
passes 36 bytes to copy_from_user(), reading past the user buffer when
size < 36.
Fix both issues by:
- Returning -ENODEV when connector->base.state or state->crtc is NULL
- Clamping write_size to min(size, sizeof(data))
(cherry picked from commit 6ab4c36a522842ff70474a1c0af2e40e50fc8300) |
| In the Linux kernel, the following vulnerability has been resolved:
dm log: fix out-of-bounds write due to region_count overflow
The local variable region_count in create_log_context() is declared as
unsigned int (32-bit), but dm_sector_div_up() returns sector_t (64-bit).
When a device-mapper target has a sufficiently large ti->len with a small
region_size, the division result can exceed UINT_MAX. The truncated
value is then used to calculate bitset_size, causing clean_bits,
sync_bits, and recovering_bits to be allocated far smaller than needed
for the actual number of regions.
Subsequent log operations (log_set_bit, log_clear_bit, log_test_bit) use
region indices derived from the full untruncated region space, causing
out-of-bounds writes to kernel heap memory allocated by vmalloc.
This can be reproduced by creating a mirror target whose region_count
overflows 32 bits:
dmsetup create bigzero --table '0 8589934594 zero'
dmsetup create mymirror --table '0 8589934594 mirror \
core 2 2 nosync 2 /dev/mapper/bigzero 0 \
/dev/mapper/bigzero 0'
The status output confirms the truncation (sync_count=1 instead of
4294967297, because 0x100000001 was truncated to 1):
$ dmsetup status mymirror
0 8589934594 mirror 2 254:1 254:1 1/4294967297 ...
This leads to a kernel crash in core_in_sync:
BUG: scheduling while atomic: (udev-worker)/9150/0x00000000
RIP: 0010:core_in_sync+0x14/0x30 [dm_log]
CR2: 0000000000000008
Fixing recursive fault but reboot is needed!
Fix by widening the local region_count to sector_t and adding an
explicit overflow check before the value is assigned to lc->region_count. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix OOB write to userspace in sctp_getsockopt_peer_auth_chunks
sctp_getsockopt_peer_auth_chunks() checks that the caller's optval
buffer is large enough for the peer AUTH chunk list with
if (len < num_chunks)
return -EINVAL;
but then writes num_chunks bytes to p->gauth_chunks, which lives
at offset offsetof(struct sctp_authchunks, gauth_chunks) == 8
inside optval. The check is missing the sizeof(struct
sctp_authchunks) = 8-byte header. When the caller supplies
len == num_chunks (for any num_chunks > 0) the test passes but
copy_to_user() writes sizeof(struct sctp_authchunks) = 8 bytes
past the declared buffer.
The sibling function sctp_getsockopt_local_auth_chunks() at the
next line already has the correct check:
if (len < sizeof(struct sctp_authchunks) + num_chunks)
return -EINVAL;
Align the peer variant with its sibling.
Reproducer confirms on v7.0-13-generic: an unprivileged userspace
caller that opens a loopback SCTP association with AUTH enabled,
queries num_chunks with a short optval, then issues the real
getsockopt with len == num_chunks and sentinel bytes painted past
the buffer observes those sentinel bytes overwritten with the
peer's AUTH chunk type. The bytes written are under the peer's
control but land in the caller's own userspace; this is not a
kernel memory corruption, but it is a kernel-side contract
violation that can silently corrupt adjacent userspace data. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix a buffer leak in __ceph_setxattr()
The old_blob in __ceph_setxattr() can store
ci->i_xattrs.prealloc_blob value during the retry.
However, it is never called the ceph_buffer_put()
for the old_blob object. This patch fixes the issue of
the buffer leak. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: fix a buffer overflow in ioctl processing
Tony Asleson (using Claude) found a buffer overflow in dm-ioctl in the
function retrieve_status:
1. The code in retrieve_status checks that the output string fits into
the output buffer and writes the output string there
2. Then, the code aligns the "outptr" variable to the next 8-byte
boundary:
outptr = align_ptr(outptr);
3. The alignment doesn't check overflow, so outptr could point past the
buffer end
4. The "for" loop is iterated again, it executes:
remaining = len - (outptr - outbuf);
5. If "outptr" points past "outbuf + len", the arithmetics wraps around
and the variable "remaining" contains unusually high number
6. With "remaining" being high, the code writes more data past the end of
the buffer
Luckily, this bug has no security implications because:
1. Only root can issue device mapper ioctls
2. The commonly used libraries that communicate with device mapper
(libdevmapper and devicemapper-rs) use buffer size that is aligned to
8 bytes - thus, "outptr = align_ptr(outptr)" can't overshoot the input
buffer and the bug can't happen accidentally |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: fix buffer size clamping order
In vsock_update_buffer_size(), the buffer size was being clamped to the
maximum first, and then to the minimum. If a user sets a minimum buffer
size larger than the maximum, the minimum check overrides the maximum
check, inverting the constraint.
This breaks the intended socket memory boundaries by allowing the
vsk->buffer_size to grow beyond the configured vsk->buffer_max_size.
Fix this by checking the minimum first, and then the maximum. This
ensures the buffer size never exceeds the buffer_max_size. |
| In the Linux kernel, the following vulnerability has been resolved:
fbcon: Avoid OOB font access if console rotation fails
Clear the font buffer if the reallocation during console rotation fails
in fbcon_rotate_font(). The putcs implementations for the rotated buffer
will return early in this case. See [1] for an example.
Currently, fbcon_rotate_font() keeps the old buffer, which is too small
for the rotated font. Printing to the rotated console with a high-enough
character code will overflow the font buffer.
v2:
- fix typos in commit message |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: fix a potential clc buffer length underflow
The buf_len is used to limit the iterations for retrieving the country
power setting and may underflow under certain conditions due to changes
in the power table in CLC.
This underflow leads to an almost infinite loop or an invalid power
setting resulting in driver initialization failure. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: nx - fix bounce buffer leaks in nx842_crypto_{alloc,free}_ctx
The bounce buffers are allocated with __get_free_pages() using
BOUNCE_BUFFER_ORDER (order 2 = 4 pages), but both the allocation error
path and nx842_crypto_free_ctx() release the buffers with free_page().
Use free_pages() with the matching order instead. |
| In the Linux kernel, the following vulnerability has been resolved:
md/md-llbitmap: skip reading rdevs that are not in_sync
When reading bitmap pages from member disks, the code iterates through
all rdevs and attempts to read from the first available one. However,
it only checks for raid_disk assignment and Faulty flag, missing the
In_sync flag check.
This can cause bitmap data to be read from spare disks that are still
being rebuilt and don't have valid bitmap information yet. Reading
stale or uninitialized bitmap data from such disks can lead to
incorrect dirty bit tracking, potentially causing data corruption
during recovery or normal operation.
Add the In_sync flag check to ensure bitmap pages are only read from
fully synchronized member disks that have valid bitmap data. |
