| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The ARM PL011 UART driver in drivers/serial/uart_pl011.c fails to acknowledge receive error interrupts. On the PL011, the framing, parity, break, and overrun error interrupts (PL011_IMSC_ERROR_MASK) are cleared only by writing the interrupt-clear register UARTICR; reading the data register clears the RX interrupt and the per-byte RSR status but not the error interrupt status in MIS. The interrupt service routine pl011_isr() acknowledged only the CTS modem-status interrupt and never wrote icr for the error bits, so an asserted error interrupt remains pending after the ISR returns.
When an application enables error-interrupt reporting via the public uart_irq_err_enable() API, an attacker who controls the serial peer can deterministically assert these error bits by injecting line errors on the RX line — a baud/stop-bit mismatch or mid-character break (framing/break error), a flipped parity bit (parity error), or FIFO flooding (overrun error). Because the error interrupt is never cleared, the interrupt line stays asserted and the CPU re-enters pl011_isr() immediately and indefinitely, producing an interrupt-storm livelock from which the core makes no forward progress.
The impact is an availability-only denial of service (permanent hang), reachable from an external or removable UART peer. Exploitation is gated by configuration: the error interrupt is off by default and no in-tree subsystem enables it, so only applications that explicitly call uart_irq_err_enable() on a PL011-based, interrupt-driven port are affected. The fix makes pl011_isr() acknowledge the pending error bits via uart->icr, breaking the loop, and additionally clears the latched RSR status in pl011_err_check(). |
| Zephyr's IPv6 forwarding path re-sent routed unicast packets without ever decrementing the IPv6 hop limit. Both routing branches of ipv6_route_packet() (subsys/net/ip) were affected: the explicit-route path (net_route_packet()) and the on-link cross-interface path (net_route_packet_if()). Each set the packet forwarding flag and called net_send_data() with the hop limit untouched and no expiry check.
Per RFC 8200 the hop-limit decrement is the mechanism that bounds packet lifetime and terminates routing loops; without it, a device acting as an IPv6 router relays looping packets indefinitely. An on-path attacker who can induce or exploit a transient L3 loop turns it into a permanent forwarding storm, causing CPU/bandwidth resource exhaustion (availability DoS) on the forwarder and adjacent links; path-discovery and loop diagnostics that rely on hop-limit expiry are also defeated.
Affected configurations. In every affected release the forwarding path is reached via CONFIG_NET_ROUTE (enabled by default when CONFIG_NET_IPV6_NBR_CACHE is set), together with CONFIG_NET_ROUTING for cross-interface routing. Note that CONFIG_NET_IPV6_FORWARDING and CONFIG_NET_IPV4_FORWARDING — which appear in the fix and in this advisory's evidence notes — were introduced after v4.4.0, when the routing options were split and renamed; they do not exist in any affected release. When auditing a v4.4.1-or-earlier configuration, look for CONFIG_NET_ROUTE and CONFIG_NET_ROUTING.
IPv4 is not affected in any release. The IPv4 forwarding path (net_route_ipv4_packet() in route_ipv4.c) was added after v4.4.0 and has never shipped in a release. Its TTL decrement and IPv4 header-checksum recomputation landed on main as part of the same fix, so the evidence notes below discuss it, but no released version is reachable by way of IPv4.
Affected releases are v1.8.0 through v4.4.1: v1.8.0 introduced net_route_packet() and v2.2.0 added net_route_packet_if(), and neither decremented the hop limit. v4.3.1 carries the explicit-route fix but not the on-link one, so it is affected as well. Fixed on main by 7d8f1afa7345 (explicit-route path) and 589eadc74efa (on-link path). |
| The Zephyr PL011 UART driver (drivers/serial/uart_pl011.c) contains an unbounded software loop in pl011_irq_tx_enable() that repeatedly invokes the interrupt-driven application callback while the TX interrupt mask bit (PL011_IMSC_TXIM) is set, to work around the controller's level-transition TX-interrupt behavior.
When CTS hardware flow control is enabled (devicetree hw-flow-control or runtime UART_CFG_FLOW_CTRL_RTS_CTS) and the wired serial peer de-asserts CTS, the controller stops draining the TX FIFO; pl011_fifo_fill() then returns 0 on every call while the application still has pending data and therefore never disables the TX interrupt. The loop condition never clears, so the thread that called uart_irq_tx_enable() (e.g. h4_send() in the Bluetooth HCI H4 driver) spins indefinitely, hanging the executing context and stalling the transport — a denial of service (CWE-835).
An attacker controlling the device attached to the UART's CTS line can trigger the hang by withholding CTS during transmission. Because that peer is the device wired to the UART — which may be a removable or external module (e.g. an off-board Bluetooth controller on the HCI H4 link) rather than a permanently-bonded on-PCB part — the attack vector is scored Adjacent (AV:A) rather than Physical; the security subcommittee should confirm the vector against the specific deployment. Impact is availability only; there is no memory-safety, confidentiality, or integrity consequence.
The vulnerable loop was introduced in commit b783bc8448ef (Feb 2025) and shipped in releases v4.1.0 through v4.4.0. The fix breaks out of the loop when CTS is blocking and arms the CTS modem-status interrupt to resume transmission when CTS re-asserts. |
| isomorphic-git is a pure JavaScript implementation of Git for Node.js and browsers. Prior to 1.38.6, isomorphic-git persists server-supplied circular symref= capabilities through updateRemoteRefs, and GitRefManager.resolve() follows the resulting loose symbolic references without a default depth limit or cycle detection. After a clone from a malicious or man-in-the-middle-controlled remote, operations such as log, status, checkout, and branch that resolve refs/remotes/origin/a or refs/remotes/origin/b do not terminate. The circular references remain on disk, leaving the repository unusable for the application and causing a persistent denial of service. This issue is fixed in version 1.38.6. |
| MariaDB Connector/J is used to connect applications developed in Java to MariaDB and MySQL databases. From 3.0.0 until 3.3.7, 3.4.5, and 3.5.11, the connector assumed result bytes were UTF-8 but guarded only changes to character_set_client. It did not reject non-UTF-8 character_set_results changes and relied on the server's global session_track_system_variables configuration to report character-set changes. A malicious or compromised server, or a machine-in-the-middle attacker, could suppress tracking or change the result charset so application strings differed from the returned bytes, potentially defeating application-side validation or escaping that depended on the decoded values. This issue is fixed in versions 3.3.7, 3.4.5, and 3.5.11. |
| FreeRDP before 3.32.2 contains a denial of service vulnerability in the shadow server that allows authenticated RDP clients to spin server threads by sending zero-length drdynvc DATA PDUs. Attackers can send empty DATA messages on opened audin or rdpgfx channels, so that FreeRDP_WTSVirtualChannelRead never consumes them, consuming full CPU cores until disconnect. |
| FreeRDP before 3.32.2 contains a denial-of-service vulnerability in rdg_process_control_packet that allows a malicious RD Gateway to exhaust client CPU by sending an incomplete keepalive control packet. Attackers completing the RDG tunnel-open exchange then send an eight-byte header with packetLength 0xFFFF and withhold the body, causing an unbounded no-progress read loop that spins one client thread at full CPU. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| A vulnerability has been found in phpMyAdmin ShapeFile up to 4.0.1. Impacted is the function ShapeRecord::loadFromFile of the component SHP File Handler. Such manipulation leads to infinite loop. The attack can be executed remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way. |
| imagecodecs 2026.3.6 through 2026.10.10 contains an infinite loop vulnerability in ccitt_fax4_decode_size() that allows attackers to hang the calling process by supplying a crafted CCITT Group 4 stream. Attackers can provide an 8-byte G4 stream lacking EOFB to ccittfax4_decode() or the numcodecs Ccittfax4 codec, consuming full CPU until the process is killed. |
| The VobSub subtitle decoder libsub_vob (part of the Amlogic DroidLogic SubTitleService), as shipped on Nexbox A95X (Amlogic S905X) TV boxes, contains an infinite loop vulnerability in get_vob_spu() that allows unauthenticated network attackers or local users loading malicious files to trigger an unreachable loop exit condition via mismatched length fields. Attackers can send crafted AMLU data blocks over the unauthenticated tcp/10100 listener or via a malicious VobSub (.sub) file to cause the subtitle decode thread to spin at 100% CPU indefinitely, resulting in denial of service. |
| Kvazaar through 2.3.2 contains an infinite loop vulnerability in read_header() in src/encmain.c that allows attackers to hang the command-line encoder by supplying a truncated Y4M header. Attackers can provide a crafted .y4m file lacking a terminating newline, causing unchecked EOF reads that hang the process indefinitely while consuming a full CPU core. |
| A remotely exploitable denial-of-service vulnerability exists in the TCP options parser of the Nut/Net TCP/IP stack included in Nut/OS, developed by Ethernut/Egnite. Nut/OS releases up to version 5.1 are affected. An unauthenticated attacker can send a single TCP segment containing an unknown TCP option with a length byte of zero to any open TCP port on a vulnerable device. When processed, this malformed option triggers an infinite loop in the function NutTcpInputOptions, permanently blocking the TCP processing thread and rendering all TCP-based services unresponsive until the device is rebooted. |
| HDF5 through 2.2.0 contains an uncontrolled recursion vulnerability in H5B__iterate_helper() in src/H5B.c. When iterating a version 1 B-tree, the function does not verify that a child node’s level matches the expected level. That check is performed only in H5B__cache_deserialize() when a node is first loaded into the metadata cache. A crafted HDF5 file whose B-tree child pointer refers back to a node already in the cache, such as a node that points to itself, bypasses the check and causes unbounded recursion, leading to stack exhaustion and a crash. This can be triggered by calling H5Gget_info() or H5Gget_num_objs() on a group in the crafted file, which reaches H5B_iterate() through H5G__obj_info() and H5G__stab_count(). An attacker who can get a user or application to open a malicious file can cause a denial of service. |
| Infinite loop in Xpdf 4.06 and earlier, due to incorrect validation of progression order field in JPEG 2000 image. |
| GNU mtools before 4.0.50 has an out-of-bounds write in parse_vses in vfat.c. |
| In Eclipse ThreadX versions 6.0.1 through 6.5.2.202603, the Module Manager loaders return an overflow error without releasing the Module Manager mutex when a module preamble declares a data or stack size that overflows the allocation arithmetic. Loading such an image blocks every later module load, start, stop and unload from other threads until the system is reset. |
| pypdf is a free and open-source pure-python PDF library. Prior to 6.20.0, an attacker can craft an incomplete PDF that ends inside a standard cross-reference table, causing pypdf to mishandle the unexpected end of file and enter an infinite loop. This issue is fixed in version 6.20.0. |
| pypdf is a free and open-source pure-python PDF library. An attacker who uses a vulnerability present in versions prior to 6.10.1 can craft a PDF which leads to long runtimes. This requires cross-reference streams with wrong large `/Size` values or object streams with wrong large `/N` values. This has been fixed in pypdf 6.10.1. As a workaround, one may apply the changes from the patch manually. |
| pypdf is a free and open-source pure-python PDF library. An attacker who uses a vulnerability present in versions 3.7.0 through 3.16.4 can craft a PDF which leads to an infinite loop. This infinite loop blocks the current process and can utilize a single core of the CPU by 100%. It does not affect memory usage. That is, for example, the case when the pypdf-user manipulates an incoming malicious PDF e.g. by merging it with another PDF or by adding annotations. The issue was fixed in version 3.17.0. As a workaround, apply the patch manually by modifying `pypdf/generic/_data_structures.py`. |
