| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Concurrent execution using shared resource with improper synchronization ('race condition') in .NET Framework allows an unauthorized attacker to deny service over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
clocksource/drivers/sh_tmu: Always leave device running after probe
The TMU device can be used as both a clocksource and a clockevent
provider. The driver tries to be smart and power itself on and off, as
well as enabling and disabling its clock when it's not in operation.
This behavior is slightly altered if the TMU is used as an early
platform device in which case the device is left powered on after probe,
but the clock is still enabled and disabled at runtime.
This has worked for a long time, but recent improvements in PREEMPT_RT
and PROVE_LOCKING have highlighted an issue. As the TMU registers itself
as a clockevent provider, clockevents_register_device(), it needs to use
raw spinlocks internally as this is the context of which the clockevent
framework interacts with the TMU driver. However in the context of
holding a raw spinlock the TMU driver can't really manage its power
state or clock with calls to pm_runtime_*() and clk_*() as these calls
end up in other platform drivers using regular spinlocks to control
power and clocks.
This mix of spinlock contexts trips a lockdep warning.
=============================
[ BUG: Invalid wait context ]
6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted
-----------------------------
swapper/0/0 is trying to lock:
ffff000008c9e180 (&dev->power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88
other info that might help us debug this:
context-{5:5}
1 lock held by swapper/0/0:
ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0
#0: ffff8000817ec298
ccree e6601000.crypto: ARM ccree device initialized
(tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8
stack backtrace:
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT
Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
Call trace:
show_stack+0x14/0x1c (C)
dump_stack_lvl+0x6c/0x90
dump_stack+0x14/0x1c
__lock_acquire+0x904/0x1584
lock_acquire+0x220/0x34c
_raw_spin_lock_irqsave+0x58/0x80
__pm_runtime_resume+0x38/0x88
sh_tmu_clock_event_set_oneshot+0x84/0xd4
clockevents_switch_state+0xfc/0x13c
tick_broadcast_set_event+0x30/0xa4
__tick_broadcast_oneshot_control+0x1e0/0x3a8
tick_broadcast_oneshot_control+0x30/0x40
cpuidle_enter_state+0x40c/0x680
cpuidle_enter+0x30/0x40
do_idle+0x1f4/0x280
cpu_startup_entry+0x34/0x40
kernel_init+0x0/0x130
do_one_initcall+0x0/0x230
__primary_switched+0x88/0x90
For non-PREEMPT_RT builds this is not really an issue, but for
PREEMPT_RT builds where normal spinlocks can sleep this might be an
issue. Be cautious and always leave the power and clock running after
probe. |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: fix invalid folio access when i_blkbits differs from I/O granularity
Commit aa35dd5cbc06 ("iomap: fix invalid folio access after
folio_end_read()") partially addressed invalid folio access for folios
without an ifs attached, but it did not handle the case where
1 << inode->i_blkbits matches the folio size but is different from the
granularity used for the IO, which means IO can be submitted for less
than the full folio for the !ifs case.
In this case, the condition:
if (*bytes_submitted == folio_len)
ctx->cur_folio = NULL;
in iomap_read_folio_iter() will not invalidate ctx->cur_folio, and
iomap_read_end() will still be called on the folio even though the IO
helper owns it and will finish the read on it.
Fix this by unconditionally invalidating ctx->cur_folio for the !ifs
case. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_hid: move list and spinlock inits from bind to alloc
There was an issue when you did the following:
- setup and bind an hid gadget
- open /dev/hidg0
- use the resulting fd in EPOLL_CTL_ADD
- unbind the UDC
- bind the UDC
- use the fd in EPOLL_CTL_DEL
When CONFIG_DEBUG_LIST was enabled, a list_del corruption was reported
within remove_wait_queue (via ep_remove_wait_queue). After some
debugging I found out that the queues, which f_hid registers via
poll_wait were the problem. These were initialized using
init_waitqueue_head inside hidg_bind. So effectively, the bind function
re-initialized the queues while there were still items in them.
The solution is to move the initialization from hidg_bind to hidg_alloc
to extend their lifetimes to the lifetime of the function instance.
Additionally, I found many other possibly problematic init calls in the
bind function, which I moved as well. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: server: make use of smbdirect_socket.send_io.bcredits
It turns out that our code will corrupt the stream of
reassabled data transfer messages when we trigger an
immendiate (empty) send.
In order to fix this we'll have a single 'batch' credit per
connection. And code getting that credit is free to use
as much messages until remaining_length reaches 0, then
the batch credit it given back and the next logical send can
happen. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: server: make use of smbdirect_socket.recv_io.credits.available
The logic off managing recv credits by counting posted recv_io and
granted credits is racy.
That's because the peer might already consumed a credit,
but between receiving the incoming recv at the hardware
and processing the completion in the 'recv_done' functions
we likely have a window where we grant credits, which
don't really exist.
So we better have a decicated counter for the
available credits, which will be incremented
when we posted new recv buffers and drained when
we grant the credits to the peer.
This fixes regression Namjae reported with
the 6.18 release. |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: bcm: bcm2835-power: Increase ASB control timeout
The bcm2835_asb_control() function uses a tight polling loop to wait
for the ASB bridge to acknowledge a request. During intensive workloads,
this handshake intermittently fails for V3D's master ASB on BCM2711,
resulting in "Failed to disable ASB master for v3d" errors during
runtime PM suspend. As a consequence, the failed power-off leaves V3D in
a broken state, leading to bus faults or system hangs on later accesses.
As the timeout is insufficient in some scenarios, increase the polling
timeout from 1us to 5us, which is still negligible in the context of a
power domain transition. Also, replace the open-coded ktime_get_ns()/
cpu_relax() polling loop with readl_poll_timeout_atomic(). |
| An Incorrect Synchronization vulnerability in the management daemon (mgd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based attacker with low privileges to cause a complete Denial-of-Service (DoS) of the management plane.
When NETCONF sessions are quickly established and disconnected, a locking issue causes mgd processes to hang in an unusable state. When the maximum number of mgd processes has been reached, no new logins are possible. This leads to the inability to manage the device and requires a power-cycle to recover.
This issue can be monitored by checking for mgd processes in lockf state in the output of 'show system processes extensive':
user@host> show system processes extensive | match mgd
<pid> root 20 0 501M 4640K lockf 1 0:01 0.00% mgd
If the system still can be accessed (either via the CLI or as root, which might still be possible as last resort as this won't invoke mgd), mgd processes in this state can be killed with 'request system process terminate <PID>' from the CLI or with 'kill -9 <PID>' from the shell.
This issue affects:
Junos OS:
* 23.4 versions before 23.4R2-S4,
* 24.2 versions before 24.2R2-S1,
* 24.4 versions before 24.4R1-S3, 24.4R2;
This issue does not affect Junos OS versions before 23.4R1;
Junos OS Evolved:
* 23.4 versions before 23.4R2-S5-EVO,
* 24.2 versions before 24.2R2-S1-EVO,
* 24.4 versions before 24.4R1-S3-EVO, 24.4R2-EVO.
This issue does not affect Junos OS Evolved versions before 23.4R1-EVO; |
| A denial of service may be caused to a single peripheral device in a BLE network when multiple central
devices continuously connect and disconnect to the peripheral. A hard reset is required to recover the peripheral device. |
| In chainmaker-go (aka ChainMaker) before 2.4.0, when making frequent updates to a node's configuration file and restarting this node, concurrent writes by logger.go to a map are mishandled. Creating other logs simultaneously can lead to a read-write conflict and panic. |
| In chainmaker-go (aka ChainMaker) before 2.3.6, multiple updates to a single node's configuration can cause other normal nodes to perform concurrent read and write operations on a map, leading to a panic. |
| In the Linux kernel, the following vulnerability has been resolved:
w1: fix WARNING after calling w1_process()
I got the following WARNING message while removing driver(ds2482):
------------[ cut here ]------------
do not call blocking ops when !TASK_RUNNING; state=1 set at [<000000002d50bfb6>] w1_process+0x9e/0x1d0 [wire]
WARNING: CPU: 0 PID: 262 at kernel/sched/core.c:9817 __might_sleep+0x98/0xa0
CPU: 0 PID: 262 Comm: w1_bus_master1 Tainted: G N 6.1.0-rc3+ #307
RIP: 0010:__might_sleep+0x98/0xa0
Call Trace:
exit_signals+0x6c/0x550
do_exit+0x2b4/0x17e0
kthread_exit+0x52/0x60
kthread+0x16d/0x1e0
ret_from_fork+0x1f/0x30
The state of task is set to TASK_INTERRUPTIBLE in loop in w1_process(),
set it to TASK_RUNNING when it breaks out of the loop to avoid the
warning. |
| lunary-ai/lunary is vulnerable to an authentication issue due to improper validation of email addresses during the signup process. Specifically, the server fails to treat email addresses as case insensitive, allowing the creation of multiple accounts with the same email address by varying the case of the email characters. For example, accounts for 'abc@gmail.com' and 'Abc@gmail.com' can both be created, leading to potential impersonation and confusion among users. |
| FISCO BCOS 3.11.0 has an issue with synchronization of the transaction pool that can, for example, be observed when a malicious node (that has modified the codebase to allow a large min_seal_time value) joins a blockchain network. |
| A background script invoking <code>requestFullscreen</code> and then blocking the main thread could force the browser into fullscreen mode indefinitely, resulting in potential user confusion or spoofing attacks. This vulnerability affects Firefox < 110, Thunderbird < 102.8, and Firefox ESR < 102.8. |
| lunary-ai/lunary is vulnerable to a session reuse attack, allowing a removed user to change the organization name without proper authorization. The vulnerability stems from the lack of validation to check if a user is still part of an organization before allowing them to make changes. An attacker can exploit this by using an old authorization token to send a PATCH request, modifying the organization's name even after being removed from the organization. This issue is due to incorrect synchronization and affects the orgs.patch route. |
| In lunary-ai/lunary versions <=v1.2.11, an attacker can bypass email validation by using a dot character ('.') in the email address. This allows the creation of multiple accounts with essentially the same email address (e.g., 'attacker123@gmail.com' and 'attacker.123@gmail.com'), leading to incorrect synchronization and potential security issues. |
| Incorrect Synchronization in GitHub repository polonel/trudesk prior to 1.2.3. |
| An information disclosure issue has been discovered in GitLab EE affecting all versions starting from 16.5 prior to 17.2.8, from 17.3 prior to 17.3.4, and from 17.4 prior to 17.4.1. A maintainer could obtain a Dependency Proxy password by editing a certain Dependency Proxy setting. |
