| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
eth: bnxt: fix kernel panic in the bnxt_get_queue_stats{rx | tx}
When qstats-get operation is executed, callbacks of netdev_stats_ops
are called. The bnxt_get_queue_stats{rx | tx} collect per-queue stats
from sw_stats in the rings.
But {rx | tx | cp}_ring are allocated when the interface is up.
So, these rings are not allocated when the interface is down.
The qstats-get is allowed even if the interface is down. However,
the bnxt_get_queue_stats{rx | tx}() accesses cp_ring and tx_ring
without null check.
So, it needs to avoid accessing rings if the interface is down.
Reproducer:
ip link set $interface down
./cli.py --spec netdev.yaml --dump qstats-get
OR
ip link set $interface down
python ./stats.py
Splat looks like:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 1680fa067 P4D 1680fa067 PUD 16be3b067 PMD 0
Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 0 UID: 0 PID: 1495 Comm: python3 Not tainted 6.14.0-rc4+ #32 5cd0f999d5a15c574ac72b3e4b907341
Hardware name: ASUS System Product Name/PRIME Z690-P D4, BIOS 0603 11/01/2021
RIP: 0010:bnxt_get_queue_stats_rx+0xf/0x70 [bnxt_en]
Code: c6 87 b5 18 00 00 02 eb a2 66 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 01
RSP: 0018:ffffabef43cdb7e0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffffffc04c8710 RCX: 0000000000000000
RDX: ffffabef43cdb858 RSI: 0000000000000000 RDI: ffff8d504e850000
RBP: ffff8d506c9f9c00 R08: 0000000000000004 R09: ffff8d506bcd901c
R10: 0000000000000015 R11: ffff8d506bcd9000 R12: 0000000000000000
R13: ffffabef43cdb8c0 R14: ffff8d504e850000 R15: 0000000000000000
FS: 00007f2c5462b080(0000) GS:ffff8d575f600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000167fd0000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
<TASK>
? __die+0x20/0x70
? page_fault_oops+0x15a/0x460
? sched_balance_find_src_group+0x58d/0xd10
? exc_page_fault+0x6e/0x180
? asm_exc_page_fault+0x22/0x30
? bnxt_get_queue_stats_rx+0xf/0x70 [bnxt_en cdd546fd48563c280cfd30e9647efa420db07bf1]
netdev_nl_stats_by_netdev+0x2b1/0x4e0
? xas_load+0x9/0xb0
? xas_find+0x183/0x1d0
? xa_find+0x8b/0xe0
netdev_nl_qstats_get_dumpit+0xbf/0x1e0
genl_dumpit+0x31/0x90
netlink_dump+0x1a8/0x360 |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/code-patching: Disable KASAN report during patching via temporary mm
Erhard reports the following KASAN hit on Talos II (power9) with kernel 6.13:
[ 12.028126] ==================================================================
[ 12.028198] BUG: KASAN: user-memory-access in copy_to_kernel_nofault+0x8c/0x1a0
[ 12.028260] Write of size 8 at addr 0000187e458f2000 by task systemd/1
[ 12.028346] CPU: 87 UID: 0 PID: 1 Comm: systemd Tainted: G T 6.13.0-P9-dirty #3
[ 12.028408] Tainted: [T]=RANDSTRUCT
[ 12.028446] Hardware name: T2P9D01 REV 1.01 POWER9 0x4e1202 opal:skiboot-bc106a0 PowerNV
[ 12.028500] Call Trace:
[ 12.028536] [c000000008dbf3b0] [c000000001656a48] dump_stack_lvl+0xbc/0x110 (unreliable)
[ 12.028609] [c000000008dbf3f0] [c0000000006e2fc8] print_report+0x6b0/0x708
[ 12.028666] [c000000008dbf4e0] [c0000000006e2454] kasan_report+0x164/0x300
[ 12.028725] [c000000008dbf600] [c0000000006e54d4] kasan_check_range+0x314/0x370
[ 12.028784] [c000000008dbf640] [c0000000006e6310] __kasan_check_write+0x20/0x40
[ 12.028842] [c000000008dbf660] [c000000000578e8c] copy_to_kernel_nofault+0x8c/0x1a0
[ 12.028902] [c000000008dbf6a0] [c0000000000acfe4] __patch_instructions+0x194/0x210
[ 12.028965] [c000000008dbf6e0] [c0000000000ade80] patch_instructions+0x150/0x590
[ 12.029026] [c000000008dbf7c0] [c0000000001159bc] bpf_arch_text_copy+0x6c/0xe0
[ 12.029085] [c000000008dbf800] [c000000000424250] bpf_jit_binary_pack_finalize+0x40/0xc0
[ 12.029147] [c000000008dbf830] [c000000000115dec] bpf_int_jit_compile+0x3bc/0x930
[ 12.029206] [c000000008dbf990] [c000000000423720] bpf_prog_select_runtime+0x1f0/0x280
[ 12.029266] [c000000008dbfa00] [c000000000434b18] bpf_prog_load+0xbb8/0x1370
[ 12.029324] [c000000008dbfb70] [c000000000436ebc] __sys_bpf+0x5ac/0x2e00
[ 12.029379] [c000000008dbfd00] [c00000000043a228] sys_bpf+0x28/0x40
[ 12.029435] [c000000008dbfd20] [c000000000038eb4] system_call_exception+0x334/0x610
[ 12.029497] [c000000008dbfe50] [c00000000000c270] system_call_vectored_common+0xf0/0x280
[ 12.029561] --- interrupt: 3000 at 0x3fff82f5cfa8
[ 12.029608] NIP: 00003fff82f5cfa8 LR: 00003fff82f5cfa8 CTR: 0000000000000000
[ 12.029660] REGS: c000000008dbfe80 TRAP: 3000 Tainted: G T (6.13.0-P9-dirty)
[ 12.029735] MSR: 900000000280f032 <SF,HV,VEC,VSX,EE,PR,FP,ME,IR,DR,RI> CR: 42004848 XER: 00000000
[ 12.029855] IRQMASK: 0
GPR00: 0000000000000169 00003fffdcf789a0 00003fff83067100 0000000000000005
GPR04: 00003fffdcf78a98 0000000000000090 0000000000000000 0000000000000008
GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR12: 0000000000000000 00003fff836ff7e0 c000000000010678 0000000000000000
GPR16: 0000000000000000 0000000000000000 00003fffdcf78f28 00003fffdcf78f90
GPR20: 0000000000000000 0000000000000000 0000000000000000 00003fffdcf78f80
GPR24: 00003fffdcf78f70 00003fffdcf78d10 00003fff835c7239 00003fffdcf78bd8
GPR28: 00003fffdcf78a98 0000000000000000 0000000000000000 000000011f547580
[ 12.030316] NIP [00003fff82f5cfa8] 0x3fff82f5cfa8
[ 12.030361] LR [00003fff82f5cfa8] 0x3fff82f5cfa8
[ 12.030405] --- interrupt: 3000
[ 12.030444] ==================================================================
Commit c28c15b6d28a ("powerpc/code-patching: Use temporary mm for
Radix MMU") is inspired from x86 but unlike x86 is doesn't disable
KASAN reports during patching. This wasn't a problem at the begining
because __patch_mem() is not instrumented.
Commit 465cabc97b42 ("powerpc/code-patching: introduce
patch_instructions()") use copy_to_kernel_nofault() to copy several
instructions at once. But when using temporary mm the destination is
not regular kernel memory but a kind of kernel-like memory located
in user address space.
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd/iova_bitmap: Fix shift-out-of-bounds in iova_bitmap_offset_to_index()
Resolve a UBSAN shift-out-of-bounds issue in iova_bitmap_offset_to_index()
where shifting the constant "1" (of type int) by bitmap->mapped.pgshift
(an unsigned long value) could result in undefined behavior.
The constant "1" defaults to a 32-bit "int", and when "pgshift" exceeds
31 (e.g., pgshift = 63) the shift operation overflows, as the result
cannot be represented in a 32-bit type.
To resolve this, the constant is updated to "1UL", promoting it to an
unsigned long type to match the operand's type. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/ASPM: Fix link state exit during switch upstream function removal
Before 456d8aa37d0f ("PCI/ASPM: Disable ASPM on MFD function removal to
avoid use-after-free"), we would free the ASPM link only after the last
function on the bus pertaining to the given link was removed.
That was too late. If function 0 is removed before sibling function,
link->downstream would point to free'd memory after.
After above change, we freed the ASPM parent link state upon any function
removal on the bus pertaining to a given link.
That is too early. If the link is to a PCIe switch with MFD on the upstream
port, then removing functions other than 0 first would free a link which
still remains parent_link to the remaining downstream ports.
The resulting GPFs are especially frequent during hot-unplug, because
pciehp removes devices on the link bus in reverse order.
On that switch, function 0 is the virtual P2P bridge to the internal bus.
Free exactly when function 0 is removed -- before the parent link is
obsolete, but after all subordinate links are gone.
[kwilczynski: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtlwifi: remove unused check_buddy_priv
Commit 2461c7d60f9f ("rtlwifi: Update header file") introduced a global
list of private data structures.
Later on, commit 26634c4b1868 ("rtlwifi Modify existing bits to match
vendor version 2013.02.07") started adding the private data to that list at
probe time and added a hook, check_buddy_priv to find the private data from
a similar device.
However, that function was never used.
Besides, though there is a lock for that list, it is never used. And when
the probe fails, the private data is never removed from the list. This
would cause a second probe to access freed memory.
Remove the unused hook, structures and members, which will prevent the
potential race condition on the list and its corruption during a second
probe when probe fails. |
| In the Linux kernel, the following vulnerability has been resolved:
media: uvcvideo: Fix double free in error path
If the uvc_status_init() function fails to allocate the int_urb, it will
free the dev->status pointer but doesn't reset the pointer to NULL. This
results in the kfree() call in uvc_status_cleanup() trying to
double-free the memory. Fix it by resetting the dev->status pointer to
NULL after freeing it.
Reviewed by: Ricardo Ribalda <ribalda@chromium.org> |
| In the Linux kernel, the following vulnerability has been resolved:
topology: Keep the cpumask unchanged when printing cpumap
During fuzz testing, the following warning was discovered:
different return values (15 and 11) from vsnprintf("%*pbl
", ...)
test:keyward is WARNING in kvasprintf
WARNING: CPU: 55 PID: 1168477 at lib/kasprintf.c:30 kvasprintf+0x121/0x130
Call Trace:
kvasprintf+0x121/0x130
kasprintf+0xa6/0xe0
bitmap_print_to_buf+0x89/0x100
core_siblings_list_read+0x7e/0xb0
kernfs_file_read_iter+0x15b/0x270
new_sync_read+0x153/0x260
vfs_read+0x215/0x290
ksys_read+0xb9/0x160
do_syscall_64+0x56/0x100
entry_SYSCALL_64_after_hwframe+0x78/0xe2
The call trace shows that kvasprintf() reported this warning during the
printing of core_siblings_list. kvasprintf() has several steps:
(1) First, calculate the length of the resulting formatted string.
(2) Allocate a buffer based on the returned length.
(3) Then, perform the actual string formatting.
(4) Check whether the lengths of the formatted strings returned in
steps (1) and (2) are consistent.
If the core_cpumask is modified between steps (1) and (3), the lengths
obtained in these two steps may not match. Indeed our test includes cpu
hotplugging, which should modify core_cpumask while printing.
To fix this issue, cache the cpumask into a temporary variable before
calling cpumap_print_{list, cpumask}_to_buf(), to keep it unchanged
during the printing process. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/dp_mst: Fix resetting msg rx state after topology removal
If the MST topology is removed during the reception of an MST down reply
or MST up request sideband message, the
drm_dp_mst_topology_mgr::up_req_recv/down_rep_recv states could be reset
from one thread via drm_dp_mst_topology_mgr_set_mst(false), racing with
the reading/parsing of the message from another thread via
drm_dp_mst_handle_down_rep() or drm_dp_mst_handle_up_req(). The race is
possible since the reader/parser doesn't hold any lock while accessing
the reception state. This in turn can lead to a memory corruption in the
reader/parser as described by commit bd2fccac61b4 ("drm/dp_mst: Fix MST
sideband message body length check").
Fix the above by resetting the message reception state if needed before
reading/parsing a message. Another solution would be to hold the
drm_dp_mst_topology_mgr::lock for the whole duration of the message
reception/parsing in drm_dp_mst_handle_down_rep() and
drm_dp_mst_handle_up_req(), however this would require a bigger change.
Since the fix is also needed for stable, opting for the simpler solution
in this patch. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/entry: Mark IRQ entries to fix stack depot warnings
The stack depot filters out everything outside of the top interrupt
context as an uninteresting or irrelevant part of the stack traces. This
helps with stack trace de-duplication, avoiding an explosion of saved
stack traces that share the same IRQ context code path but originate
from different randomly interrupted points, eventually exhausting the
stack depot.
Filtering uses in_irqentry_text() to identify functions within the
.irqentry.text and .softirqentry.text sections, which then become the
last stack trace entries being saved.
While __do_softirq() is placed into the .softirqentry.text section by
common code, populating .irqentry.text is architecture-specific.
Currently, the .irqentry.text section on s390 is empty, which prevents
stack depot filtering and de-duplication and could result in warnings
like:
Stack depot reached limit capacity
WARNING: CPU: 0 PID: 286113 at lib/stackdepot.c:252 depot_alloc_stack+0x39a/0x3c8
with PREEMPT and KASAN enabled.
Fix this by moving the IO/EXT interrupt handlers from .kprobes.text into
the .irqentry.text section and updating the kprobes blacklist to include
the .irqentry.text section.
This is done only for asynchronous interrupts and explicitly not for
program checks, which are synchronous and where the context beyond the
program check is important to preserve. Despite machine checks being
somewhat in between, they are extremely rare, and preserving context
when possible is also of value.
SVCs and Restart Interrupts are not relevant, one being always at the
boundary to user space and the other being a one-time thing.
IRQ entries filtering is also optionally used in ftrace function graph,
where the same logic applies. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_inner: incorrect percpu area handling under softirq
Softirq can interrupt ongoing packet from process context that is
walking over the percpu area that contains inner header offsets.
Disable bh and perform three checks before restoring the percpu inner
header offsets to validate that the percpu area is valid for this
skbuff:
1) If the NFT_PKTINFO_INNER_FULL flag is set on, then this skbuff
has already been parsed before for inner header fetching to
register.
2) Validate that the percpu area refers to this skbuff using the
skbuff pointer as a cookie. If there is a cookie mismatch, then
this skbuff needs to be parsed again.
3) Finally, validate if the percpu area refers to this tunnel type.
Only after these three checks the percpu area is restored to a on-stack
copy and bh is enabled again.
After inner header fetching, the on-stack copy is stored back to the
percpu area. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: use ieee80211_purge_tx_queue() to purge TX skb
When removing kernel modules by:
rmmod rtw88_8723cs rtw88_8703b rtw88_8723x rtw88_sdio rtw88_core
Driver uses skb_queue_purge() to purge TX skb, but not report tx status
causing "Have pending ack frames!" warning. Use ieee80211_purge_tx_queue()
to correct this.
Since ieee80211_purge_tx_queue() doesn't take locks, to prevent racing
between TX work and purge TX queue, flush and destroy TX work in advance.
wlan0: deauthenticating from aa:f5:fd:60:4c:a8 by local
choice (Reason: 3=DEAUTH_LEAVING)
------------[ cut here ]------------
Have pending ack frames!
WARNING: CPU: 3 PID: 9232 at net/mac80211/main.c:1691
ieee80211_free_ack_frame+0x5c/0x90 [mac80211]
CPU: 3 PID: 9232 Comm: rmmod Tainted: G C
6.10.1-200.fc40.aarch64 #1
Hardware name: pine64 Pine64 PinePhone Braveheart
(1.1)/Pine64 PinePhone Braveheart (1.1), BIOS 2024.01 01/01/2024
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ieee80211_free_ack_frame+0x5c/0x90 [mac80211]
lr : ieee80211_free_ack_frame+0x5c/0x90 [mac80211]
sp : ffff80008c1b37b0
x29: ffff80008c1b37b0 x28: ffff000003be8000 x27: 0000000000000000
x26: 0000000000000000 x25: ffff000003dc14b8 x24: ffff80008c1b37d0
x23: ffff000000ff9f80 x22: 0000000000000000 x21: 000000007fffffff
x20: ffff80007c7e93d8 x19: ffff00006e66f400 x18: 0000000000000000
x17: ffff7ffffd2b3000 x16: ffff800083fc0000 x15: 0000000000000000
x14: 0000000000000000 x13: 2173656d61726620 x12: 6b636120676e6964
x11: 0000000000000000 x10: 000000000000005d x9 : ffff8000802af2b0
x8 : ffff80008c1b3430 x7 : 0000000000000001 x6 : 0000000000000001
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000003be8000
Call trace:
ieee80211_free_ack_frame+0x5c/0x90 [mac80211]
idr_for_each+0x74/0x110
ieee80211_free_hw+0x44/0xe8 [mac80211]
rtw_sdio_remove+0x9c/0xc0 [rtw88_sdio]
sdio_bus_remove+0x44/0x180
device_remove+0x54/0x90
device_release_driver_internal+0x1d4/0x238
driver_detach+0x54/0xc0
bus_remove_driver+0x78/0x108
driver_unregister+0x38/0x78
sdio_unregister_driver+0x2c/0x40
rtw_8723cs_driver_exit+0x18/0x1000 [rtw88_8723cs]
__do_sys_delete_module.isra.0+0x190/0x338
__arm64_sys_delete_module+0x1c/0x30
invoke_syscall+0x74/0x100
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x3c/0x158
el0t_64_sync_handler+0x120/0x138
el0t_64_sync+0x194/0x198
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Fix deadloop issue on reading trace_pipe
Soft lockup occurs when reading file 'trace_pipe':
watchdog: BUG: soft lockup - CPU#6 stuck for 22s! [cat:4488]
[...]
RIP: 0010:ring_buffer_empty_cpu+0xed/0x170
RSP: 0018:ffff88810dd6fc48 EFLAGS: 00000246
RAX: 0000000000000000 RBX: 0000000000000246 RCX: ffffffff93d1aaeb
RDX: ffff88810a280040 RSI: 0000000000000008 RDI: ffff88811164b218
RBP: ffff88811164b218 R08: 0000000000000000 R09: ffff88815156600f
R10: ffffed102a2acc01 R11: 0000000000000001 R12: 0000000051651901
R13: 0000000000000000 R14: ffff888115e49500 R15: 0000000000000000
[...]
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8d853c2000 CR3: 000000010dcd8000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__find_next_entry+0x1a8/0x4b0
? peek_next_entry+0x250/0x250
? down_write+0xa5/0x120
? down_write_killable+0x130/0x130
trace_find_next_entry_inc+0x3b/0x1d0
tracing_read_pipe+0x423/0xae0
? tracing_splice_read_pipe+0xcb0/0xcb0
vfs_read+0x16b/0x490
ksys_read+0x105/0x210
? __ia32_sys_pwrite64+0x200/0x200
? switch_fpu_return+0x108/0x220
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Through the vmcore, I found it's because in tracing_read_pipe(),
ring_buffer_empty_cpu() found some buffer is not empty but then it
cannot read anything due to "rb_num_of_entries() == 0" always true,
Then it infinitely loop the procedure due to user buffer not been
filled, see following code path:
tracing_read_pipe() {
... ...
waitagain:
tracing_wait_pipe() // 1. find non-empty buffer here
trace_find_next_entry_inc() // 2. loop here try to find an entry
__find_next_entry()
ring_buffer_empty_cpu(); // 3. find non-empty buffer
peek_next_entry() // 4. but peek always return NULL
ring_buffer_peek()
rb_buffer_peek()
rb_get_reader_page()
// 5. because rb_num_of_entries() == 0 always true here
// then return NULL
// 6. user buffer not been filled so goto 'waitgain'
// and eventually leads to an deadloop in kernel!!!
}
By some analyzing, I found that when resetting ringbuffer, the 'entries'
of its pages are not all cleared (see rb_reset_cpu()). Then when reducing
the ringbuffer, and if some reduced pages exist dirty 'entries' data, they
will be added into 'cpu_buffer->overrun' (see rb_remove_pages()), which
cause wrong 'overrun' count and eventually cause the deadloop issue.
To fix it, we need to clear every pages in rb_reset_cpu(). |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Fix possible data races in gfs2_show_options()
Some fields such as gt_logd_secs of the struct gfs2_tune are accessed
without holding the lock gt_spin in gfs2_show_options():
val = sdp->sd_tune.gt_logd_secs;
if (val != 30)
seq_printf(s, ",commit=%d", val);
And thus can cause data races when gfs2_show_options() and other functions
such as gfs2_reconfigure() are concurrently executed:
spin_lock(>->gt_spin);
gt->gt_logd_secs = newargs->ar_commit;
To fix these possible data races, the lock sdp->sd_tune.gt_spin is
acquired before accessing the fields of gfs2_tune and released after these
accesses.
Further changes by Andreas:
- Don't hold the spin lock over the seq_printf operations. |
| In the Linux kernel, the following vulnerability has been resolved:
dm integrity: call kmem_cache_destroy() in dm_integrity_init() error path
Otherwise the journal_io_cache will leak if dm_register_target() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: base: Free devm resources when unregistering a device
In the current code, devres_release_all() only gets called if the device
has a bus and has been probed.
This leads to issues when using bus-less or driver-less devices where
the device might never get freed if a managed resource holds a reference
to the device. This is happening in the DRM framework for example.
We should thus call devres_release_all() in the device_del() function to
make sure that the device-managed actions are properly executed when the
device is unregistered, even if it has neither a bus nor a driver.
This is effectively the same change than commit 2f8d16a996da ("devres:
release resources on device_del()") that got reverted by commit
a525a3ddeaca ("driver core: free devres in device_release") over
memory leaks concerns.
This patch effectively combines the two commits mentioned above to
release the resources both on device_del() and device_release() and get
the best of both worlds. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: Fix an uninit variable access bug in qrtr_tx_resume()
Syzbot reported a bug as following:
=====================================================
BUG: KMSAN: uninit-value in qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
qrtr_endpoint_post+0xf85/0x11b0 net/qrtr/af_qrtr.c:519
qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was created at:
slab_post_alloc_hook mm/slab.h:766 [inline]
slab_alloc_node mm/slub.c:3452 [inline]
__kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
__do_kmalloc_node mm/slab_common.c:967 [inline]
__kmalloc_node_track_caller+0x114/0x3b0 mm/slab_common.c:988
kmalloc_reserve net/core/skbuff.c:492 [inline]
__alloc_skb+0x3af/0x8f0 net/core/skbuff.c:565
__netdev_alloc_skb+0x120/0x7d0 net/core/skbuff.c:630
qrtr_endpoint_post+0xbd/0x11b0 net/qrtr/af_qrtr.c:446
qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
It is because that skb->len requires at least sizeof(struct qrtr_ctrl_pkt)
in qrtr_tx_resume(). And skb->len equals to size in qrtr_endpoint_post().
But size is less than sizeof(struct qrtr_ctrl_pkt) when qrtr_cb->type
equals to QRTR_TYPE_RESUME_TX in qrtr_endpoint_post() under the syzbot
scenario. This triggers the uninit variable access bug.
Add size check when qrtr_cb->type equals to QRTR_TYPE_RESUME_TX in
qrtr_endpoint_post() to fix the bug. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: fix potential array out of bounds access
Account for IWL_SEC_WEP_KEY_OFFSET when needed while verifying
key_len size in iwl_mvm_sec_key_add(). |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa: Add max vqp attr to vdpa_nl_policy for nlattr length check
The vdpa_nl_policy structure is used to validate the nlattr when parsing
the incoming nlmsg. It will ensure the attribute being described produces
a valid nlattr pointer in info->attrs before entering into each handler
in vdpa_nl_ops.
That is to say, the missing part in vdpa_nl_policy may lead to illegal
nlattr after parsing, which could lead to OOB read just like CVE-2023-3773.
This patch adds the missing nla_policy for vdpa max vqp attr to avoid
such bugs. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: pcie: Fix integer overflow in iwl_write_to_user_buf
An integer overflow occurs in the iwl_write_to_user_buf() function,
which is called by the iwl_dbgfs_monitor_data_read() function.
static bool iwl_write_to_user_buf(char __user *user_buf, ssize_t count,
void *buf, ssize_t *size,
ssize_t *bytes_copied)
{
int buf_size_left = count - *bytes_copied;
buf_size_left = buf_size_left - (buf_size_left % sizeof(u32));
if (*size > buf_size_left)
*size = buf_size_left;
If the user passes a SIZE_MAX value to the "ssize_t count" parameter,
the ssize_t count parameter is assigned to "int buf_size_left".
Then compare "*size" with "buf_size_left" . Here, "buf_size_left" is a
negative number, so "*size" is assigned "buf_size_left" and goes into
the third argument of the copy_to_user function, causing a heap overflow.
This is not a security vulnerability because iwl_dbgfs_monitor_data_read()
is a debugfs operation with 0400 privileges. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup,freezer: hold cpu_hotplug_lock before freezer_mutex
syzbot is reporting circular locking dependency between cpu_hotplug_lock
and freezer_mutex, for commit f5d39b020809 ("freezer,sched: Rewrite core
freezer logic") replaced atomic_inc() in freezer_apply_state() with
static_branch_inc() which holds cpu_hotplug_lock.
cpu_hotplug_lock => cgroup_threadgroup_rwsem => freezer_mutex
cgroup_file_write() {
cgroup_procs_write() {
__cgroup_procs_write() {
cgroup_procs_write_start() {
cgroup_attach_lock() {
cpus_read_lock() {
percpu_down_read(&cpu_hotplug_lock);
}
percpu_down_write(&cgroup_threadgroup_rwsem);
}
}
cgroup_attach_task() {
cgroup_migrate() {
cgroup_migrate_execute() {
freezer_attach() {
mutex_lock(&freezer_mutex);
(...snipped...)
}
}
}
}
(...snipped...)
}
}
}
freezer_mutex => cpu_hotplug_lock
cgroup_file_write() {
freezer_write() {
freezer_change_state() {
mutex_lock(&freezer_mutex);
freezer_apply_state() {
static_branch_inc(&freezer_active) {
static_key_slow_inc() {
cpus_read_lock();
static_key_slow_inc_cpuslocked();
cpus_read_unlock();
}
}
}
mutex_unlock(&freezer_mutex);
}
}
}
Swap locking order by moving cpus_read_lock() in freezer_apply_state()
to before mutex_lock(&freezer_mutex) in freezer_change_state(). |
