Export limit exceeded: 26153 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (26153 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-72142 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: i2c: imx: fix locked bus on SMBus block-read of 0 (atomic) SMBus 3.1 6.5.7 allows a Block Read byte count of 0, but the atomic (polling) path rejects it as -EPROTO. Worse, it returns without a NACK+STOP: the next receive cycle has already started, so the target keeps holding SDA and the bus stays stuck until a power cycle for this i2c controller. Reading I2DR to obtain the count likewise arms the next byte on the count > I2C_SMBUS_BLOCK_MAX path, which also returned -EPROTO directly and left the bus held. Handle both: NACK the in-flight dummy byte (TXAK) and extend msgs->len so the existing last-byte handling emits STOP; the dummy byte is discarded. A count of 0 is a valid empty block read; a count above I2C_SMBUS_BLOCK_MAX is still reported as -EPROTO, but only after the bus has been released. The interrupt-driven path has the same flaw from a later commit and is fixed separately, as it carries a different Fixes: tag and stable range. | ||||
| CVE-2026-72138 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: xen/gntdev: fix error handling in ioctl When gntdev_ioctl_map_grant_ref() fails to copy the operation result back to userspace after successfully adding the mapping to the list, the error path returns -EFAULT without releasing the reference acquired by gntdev_alloc_map(). The mapping remains in priv->maps with a refcount of 1, causing a memory leak and a dangling list entry. Additionally, gntdev_add_map() may modify map->index to avoid overlap with existing mappings. Therefore, the index returned to userspace must be obtained after gntdev_add_map() completes. Fix this by holding the mutex across gntdev_add_map(), retrieving the correct index, and copy_to_user(). If copy_to_user() fails, remove the mapping from the list and release the reference while still holding the lock. Fix these issues by properly handling all error cases. | ||||
| CVE-2026-72118 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: can: bcm: fix CAN frame rx/tx statistics KCSAN detected a data race within the bcm_rx_handler() when two CAN frames have been simultaneously received and processed in a single rx op by two different CPUs. Use atomic operations with (signed) long data types to access the statistics in the hot path to fix the KCSAN complaint. Additionally simplify the update and check of statistics overflow by using the atomic operations in separate bcm_update_[rx|tx]_stats() functions. The rx variant runs under bcm_rx_update_lock to prevent races when resetting the two rx counters; the tx variant runs under bcm_tx_lock and only needs to guard its own counter's overflow. As the rx path resets its values already at LONG_MAX / 100, there is no conflict between the two locking domains (bcm_rx_update_lock vs. bcm_tx_lock) even for ops that use both paths. The rx statistics update and the frames_filtered update in bcm_rx_changed() were previously performed in two separate bcm_rx_update_lock sections. For an rx op subscribed on all interfaces (ifindex == 0), bcm_rx_handler() can run concurrently on different CPUs, so a counter reset by one CPU between these two sections could leave frames_filtered larger than frames_abs on another CPU, producing a bogus (even negative) reduction percentage in procfs. Update the statistics in the same critical section as bcm_rx_changed() to close this gap, which also removes the now unneeded extra lock/unlock pair around the traffic_flags calculation. | ||||
| CVE-2026-72117 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: can: bcm: fix data race on rx_stamp/rx_ifindex in bcm_rx_handler() For an rx op subscribed on all interfaces (ifindex == 0), the same op is registered once in the shared per-netns wildcard filter list, so bcm_rx_handler() can run concurrently on different CPUs for frames arriving on different net devices. op->rx_stamp and op->rx_ifindex were written before bcm_rx_update_lock was taken, allowing concurrent writers to race each other - including a torn store of the 64-bit rx_stamp on 32-bit platforms. Beyond a torn store bcm_send_to_user() must report the timestamp/ifindex of the very same frame whose content it is delivering. So the assignment is placed in the same unbroken bcm_rx_update_lock section as the content comparison. As a side effect, the RTR-request frame feature (which never reach bcm_send_to_user()) no longer updates rx_stamp/rx_ifindex, since only the notification path needs them. | ||||
| CVE-2026-72097 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dm-verity: fix a possible NULL pointer dereference Fix a possible NULL pointer dereference dm_verity_loadpin_is_bdev_trusted if the device has no table. | ||||
| CVE-2026-72096 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dm-verity: make error counter atomic The error counter "v->corrupted_errs" was not atomic, thus it could be subject to race conditions. The call to dm_audit_log_target("max-corrupted-errors") may be skipped due to the races. | ||||
| CVE-2026-72088 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: hpsa: Fix DMA mapping leak on IOACCEL2 reset path If phys_disk->in_reset is set, the function returns directly without undoing the resources acquired for the command. Add the missing error cleanup by unmapping the IOACCEL2 SG chain block when needed, unmapping the SCSI command, and dropping the outstanding IOACCEL command count before returning. | ||||
| CVE-2026-72087 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix memory leak in lpfc_sli4_driver_resource_setup() The memory allocated for mboxq using mempool_alloc() is not freed in some of the early exit error paths. Fix that by moving the mempool_free() call to an earlier point after last use. | ||||
| CVE-2026-72086 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: xen: scsiback: Free the command tag on the TMR submit-failure path scsiback_device_action() obtains a command tag in scsiback_get_pend_req() and submits a task-management request with target_submit_tmr(). When target_submit_tmr() fails it returns < 0 and scsiback jumps to the err: label, which sends a response but frees nothing, leaking the tag. Impact: a pvSCSI guest can leak the command tags of a LUN's session, stopping the LUN, by issuing VSCSIIF_ACT_SCSI_ABORT or RESET requests whenever target_submit_tmr() fails. transport_generic_free_cmd() cannot be used here. By the time target_submit_tmr() returns an error it has already run __target_init_cmd() (so se_cmd->cmd_kref is one, not zero), and on its target_get_sess_cmd() error path it has freed se_cmd->se_tmr_req via core_tmr_release_req() while leaving SCF_SCSI_TMR_CDB set and the pointer dangling. Letting the command release run target_free_cmd_mem() would then double-free se_tmr_req. Use the same helper, which returns just the tag, on this path too. | ||||
| CVE-2026-72073 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mmc: vub300: fix use-after-free on probe failure The vub300 driver lifetime-manages its controller state using vub300->kref, with vub300_delete() freeing the mmc host when the last reference is dropped. The probe error path after the inactivity timer has been armed still bypasses that lifetime rule, however, and falls through to mmc_free_host() directly if mmc_add_host() fails. The race window is between arming the inactivity timer and reaching the probe error unwind after mmc_add_host() fails: probe thread timer/workqueue ------------ --------------- kref_init(&vub300->kref) ref = 1 kref_get(&vub300->kref) ref = 2, timer ref add_timer(inactivity_timer) fires after one second | | race window |<----------------------------------------------------> | mmc_add_host(mmc) inactivity timer fires vub300_queue_dead_work() kref_get() ref = 3 queue_work(deadwork) mmc_add_host() fails timer_delete_sync() mmc_free_host(mmc) frees vub300 deadwork runs use-after-free The inactivity timeout is one second, so this would require mmc_add_host() to both fail and take more than one second to do so. This is unlikely to happen in practice, but the error path is still wrong. timer_delete_sync() only waits for the timer callback itself. It does not flush deadwork that the callback may already have queued. As a result, queued deadwork can still hold a kref while the probe error path directly frees the backing mmc host, including the vub300 storage. Fix this by using the same lifetime mechanism as disconnect. Clear vub300->interface so that the timer callback and any queued deadwork return early and drop their references, then drop the initial probe reference and return without falling through to err_free_host. | ||||
| CVE-2026-72070 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: libertas_tf: fix use-after-free in lbtf_free_adapter() lbtf_free_adapter() calls timer_delete(&priv->command_timer), which does not wait for a running command_timer_fn() callback. lbtf_free_adapter() runs on the teardown path right before ieee80211_free_hw() frees priv, both in lbtf_remove_card() and in the probe error path. command_timer is armed by mod_timer() in lbtf_cmd() whenever a firmware command is sent. command_timer_fn() dereferences priv. If a command times out as the device is removed, command_timer_fn() runs concurrently with teardown and dereferences priv after it has been freed. This is the same use-after-free that commit 03cc8f90d053 ("wifi: libertas: fix use-after-free in lbs_free_adapter()") fixed in the sibling libertas driver. The libertas_tf variant has the identical pattern and was left unchanged. Use timer_delete_sync() so any in-flight callback completes before priv is freed. | ||||
| CVE-2026-72068 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: posix-cpu-timers: Use u64 multiplication in update_rlimit_cpu() update_rlimit_cpu() converts the RLIMIT_CPU value to nanoseconds with u64 nsecs = rlim_new * NSEC_PER_SEC; On 32-bit kernels both rlim_new (unsigned long) and NSEC_PER_SEC (1000000000L) are 32-bit, so the multiplication is performed in unsigned long and truncated for rlim_new > 4 seconds before being widened to u64. The same file already casts to u64 for the matching computation in check_process_timers(): u64 softns = (u64)soft * NSEC_PER_SEC; As a result, the truncated value is installed into the CPUCLOCK_PROF expiry cache (nextevt), causing the process CPU timer to be programmed to fire prematurely for any RLIMIT_CPU soft limit >= 5 seconds. The actual SIGXCPU/SIGKILL decision in check_process_timers() already casts to u64 and is therefore correct, so limit enforcement is not broken; only the expiry-cache programming is wrong. Apply the same cast here so both paths convert rlim_cur identically. 64-bit kernels are unaffected. | ||||
| CVE-2026-72063 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: gpio: tegra: do not call pinctrl for GPIO direction tegra_gpio_direction_input() and tegra_gpio_direction_output() already program the GPIO controller direction registers directly. The additional pinctrl_gpio_direction_input/output() calls do not add a Tegra pinctrl operation, because the Tegra pinmux ops provide GPIO request/free handling but no gpio_set_direction hook. The extra call still enters the pinctrl core and takes pctldev->mutex. Shared GPIO users can call the direction path while holding their per-line spinlock, so this otherwise redundant pinctrl direction call can sleep in an atomic context. This was found by our static analysis tool and then confirmed by manual review of tegra_gpio_probe(), the Tegra GPIO direction callbacks and the Tegra pinctrl ops. The reviewed path has a default non-sleeping struct gpio_chip while the direction callback still enters the pinctrl mutex path. A directed runtime validation kept the same non-sleeping chip registration and drove: gpio_shared_proxy_direction_output() gpiod_direction_output_raw_commit() tegra_gpio_direction_output() pinctrl_gpio_direction_output() Lockdep reported a sleep-in-atomic warning with the shared GPIO spinlock held and pinctrl_get_device_gpio_range() plus tegra_gpio_direction_output() on the stack. Do not mark the whole chip as can_sleep to paper over this: can_sleep describes whether get()/set() may sleep, and Tegra value access is MMIO. Remove the redundant pinctrl direction calls and keep pinctrl involvement in the existing request/free path. | ||||
| CVE-2026-72056 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: ena: clean up XDP TX queues when regular TX setup fails create_queues_with_size_backoff() creates XDP TX queues before setting up the regular TX path. If the subsequent allocation or creation of regular TX queues fails, the error handling paths omit the teardown of the XDP TX queues, leading to a resource leak. Fix this by explicitly destroying the XDP TX queue subset at the two missing failure points. The bug was first flagged by an experimental analysis tool we are developing for kernel memory-management bugs while analyzing v6.13-rc1. The tool is still under development and is not yet publicly available. Manual inspection confirms that the bug is still present in v7.1-rc7. An x86_64 allyesconfig build showed no new warnings. As we do not have an ENA device to test with, no runtime testing was able to be performed. | ||||
| CVE-2026-72040 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ipmi: fix refcount leak in i_ipmi_request() When a caller provides a `supplied_recv` message to i_ipmi_request(), the function increments the user's `nr_msgs` reference count. If an error occurs later, the out_err cleanup path only frees the recv_msg if the function allocated it itself (i.e., !supplied_recv). In the supplied_recv case the cleanup is skipped, leaving the reference count elevated. The caller ipmi_request_supply_msgs() does not release the supplied_recv on error, so the reference is permanently leaked. Fix this by explicitly reverting the reference count operations when a supplied recv_msg with a valid user pointer is present in the error path: decrement nr_msgs and drop the user's kref. | ||||
| CVE-2026-72039 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bnx2x: fix potential memory leak in bnx2x_alloc_mem_bp() If the allocation of fp[i].tpa_info fails, the error path will not free the struct bnx2x_fastpath allocated earlier, as it is not linked to the bp structure yet. Fix that by linking it immediately after allocation. | ||||
| CVE-2026-72030 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ata: libata-core: Reject an invalid concurrent positioning ranges count ata_dev_config_cpr() takes the number of range descriptors from buf[0] of the concurrent positioning ranges log (up to 255), which the device reports independently of the log size in the GPL directory. The count is then walked at a fixed 32-byte stride in two places with no bound: the log read here, and the INQUIRY VPD page B9h emitter, which writes one descriptor per range into the fixed 2048-byte ata_scsi_rbuf. A device reporting a count larger than its own log overflows the read buffer (up to 7704 bytes past a 512-byte slab), and a count above 62 overflows the response buffer on the emit side. Bound the count once, on probe, against both the log the device returned and the number of descriptors the VPD B9h response buffer can hold (ATA_DEV_MAX_CPR, derived from the rbuf size). Reject an out-of-range count with a warning; this keeps the emitter in bounds with no separate change there. | ||||
| CVE-2026-72015 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: fs/resctrl: Fix double-add of pseudo-locked region's RMID to free list A pseudo-locked group's RMID is freed when it is created. On unmount rmdir_all_sub() unconditionally frees all RMID of all groups, resulting in a double-free of the pseudo-locked group's RMID. The consequence of this is that the original free results in the pseudo-locked group's RMID being added to the rmid_free_lru linked list and the second free then attempts to add the same RMID entry to the rmid_free_lru again. Do not double-free a pseudo-locked group's RMID. | ||||
| CVE-2026-72010 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: cgroup/cpuset: rebind mm mempolicy to effective_mems, not mems_allowed Creating a child cpuset where cpuset.mems is never set leads to a div/0 when a VMA mempolicy with MPOL_F_RELATIVE_NODES rebinds in response to a CPU hotplug event. Reproduction steps: 1) Create a cgroup w/ cpuset controls (do not set cpuset.mems) 2) Move the task into the child cpuset 3) Create a VMA mempolicy for that task with MPOL_F_RELATIVE_NODES 4) unplug and hotplug a cpu echo 0 > /sys/devices/system/cpu/cpu1/online echo 1 > /sys/devices/system/cpu/cpu1/online 5) mempolicy rebind does a div/0 in mpol_relative_nodemask on the call to __nodes_fold() The cpuset code passes (cs->mems_allowed) which is not guaranteed to have nodes to the rebind routine. Use cs->effective_mems instead, which is guaranteed to have a non-empty nodemask once we reach that code path. [ david: add a comment, slightly rephrase description ] | ||||
| CVE-2026-72004 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix memory leak in ieee80211_register_hw() If kmemdup() fails while copying supported band structures, the error path jumps to fail_rate. This skips rate_control_deinitialize() and leaks the initialized local->rate_ctrl. Fix this by adding a fail_band label that shares the rate-control cleanup path before falling through to the remaining teardown. The bug was first flagged by an experimental analysis tool we are developing for kernel memory-management bugs while analyzing v6.13-rc1. The tool is still under development and is not yet publicly available. Manual inspection confirms that the bug is still present in v7.1-rc7. An x86_64 allyesconfig build showed no new warnings. As we do not have a suitable mac80211 device/driver combination to test with, no runtime testing was able to be performed. | ||||